| Author |
 Topic Search  Topic Options
|
Nwest 
Bronze Level
Joined: 07 Mar 2019
Location: Mora, mn
Points: 15
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: Allis 190 transmission
Posted: 10 Feb 2020 at 12:32pm |
|
Hi again everyone I'm going through an allis 190 gas serial number 7995. I have the tractor split and am in need of several transmission gears. At some point in its life it took a bit of abuse being slammed into gears by the way the gears are worn. There are a couple gears that dont appear to be made anymore. The input shaft number 70245722 being one of them. Does anyone know if its possible to get these parts new? Otherwise the salvage yards I'm sure have some. Thank you
|
 |
|
Sponsored Links
|
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 22000
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Feb 2020 at 2:41pm |
|
I don't think there's any of the transmission parts available for that tractor. That is the transmission that, if it was a 190XT, everything was replaced with beefier parts, including the shafts. They didn't update any straight 190's, as they didn't feel there would be any problem due to less HP. I'm afraid all you can hope for is used parts from a salvage yard. Be sure they understand it is a 190 tractor PRIOR TO S/N 9001. Any 190XT has different parts and any 190 after s/n 9001 has the same parts as the XT's.
|
|
Nwest
Bronze Level
Joined: 07 Mar 2019
Location: Mora, mn
Points: 15
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Feb 2020 at 8:16pm |
|
Thanks for the input Dr. Allis. On that note if anyone on this forum has a few early 190 gears I'd be interested or I may be forced to scrap if I have no luck at the yards.
|
|
MACK
Orange Level
Joined: 17 Nov 2009
Points: 7664
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Feb 2020 at 8:55pm |
|
I have a later rear end assembly from a 190XT gas, I would make a trade with you.
. MACK
|
|
JC-WI
Orange Level Access
Joined: 11 Sep 2009
Location: wisconsin
Points: 34352
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 Feb 2020 at 12:04am |
|
Just wondering if any gears from a D19 would fit up in there...
|
|
He who says there is no evil has already deceived himself
The truth is the truth, sugar coated or not. Trawler II says, "Remember that."
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 22000
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 Feb 2020 at 7:12am |
|
Nope.
|
|
lowell66dart
Orange Level
Joined: 10 Jul 2013
Location: Paulina La.
Points: 964
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 Feb 2020 at 10:01am |
|
PM sent
|
|
AC 6080 (8030,7060,200,175,D-17HC, 6040,160,6140 all gone) Farmall 1066 & 656 Hi-Clear (for sale), White 2-62 High Clearance, JD 4255 Hi Clear.
|
|
Leon B MO
Orange Level
Joined: 12 Sep 2009
Location: Old Monroe, Mo
Points: 2191
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 Feb 2020 at 5:28pm |
would the complete trans/rear end of a D-19 bolt up to the early 190 torque tube? Leon B MO
|
|
Uncle always said "Fill the back of the shovel and the front will take care of itself".
|
|
Acdiesel
Orange Level
Joined: 15 Jun 2012
Location: Rochester Ohio
Points: 2576
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 Feb 2020 at 7:15pm |
did you check with this Guy?
C.L. ad
|
|
D19 Diesel,D17 Diesel SER.3
2-D14, 2-D15 SER.II WF/NF
D15 SER.2 DIESEL
D12 SER.I, D10 Ser.II
2-720'S D21 Ser. II
Gmc,caterpillar
I'm a pharmacist (farm assist) with a PHD (post hole digger)
|
|
MACK
Orange Level
Joined: 17 Nov 2009
Points: 7664
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 Feb 2020 at 9:30pm |
|
Housing will bolt up, but input shaft is different.
. MACK
|
|
