This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Worm Gear Removal
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Jareddrew82 View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 21 Oct 2019
Location: Missouri
Points: 13 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Jareddrew82 Quote  Post ReplyReply Direct Link To This Post Topic: Worm Gear Removal
    Posted: 11 Nov 2019 at 8:18am
I have a WD45 wide front and I’m trying to clean front bolster out due to all the gunk. How do I remove the worm gear? And top bearing? Thanks

Edited by Jareddrew82 - 11 Nov 2019 at 8:22am
Back to Top
Sponsored Links


Back to Top
MACK View Drop Down
Orange Level
Orange Level


Joined: 17 Nov 2009
Points: 7664 		Post Options Post Options   Thanks (0) Thanks(0)   Quote MACK Quote  Post ReplyReply Direct Link To This Post Posted: 11 Nov 2019 at 8:50am
I think vertical shaft has to come out first, then remove two bolts on bearing cap and remove.          MACK
Back to Top
Jareddrew82 View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 21 Oct 2019
Location: Missouri
Points: 13 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Jareddrew82 Quote  Post ReplyReply Direct Link To This Post Posted: 11 Nov 2019 at 9:14am
Do you have to press the vertical pin out? Mine is very tight. Wanting to make sure I’m not tearing something up getting it apart. Thanks
Back to Top
MACK View Drop Down
Orange Level
Orange Level


Joined: 17 Nov 2009
Points: 7664 		Post Options Post Options   Thanks (0) Thanks(0)   Quote MACK Quote  Post ReplyReply Direct Link To This Post Posted: 11 Nov 2019 at 10:01pm
Take bolt and setscrew out of bottom and shaft and gear comes out the top.      MACK
Back to Top
Lon(MN) View Drop Down
Orange Level
Orange Level


Joined: 11 Sep 2009
Location: Merrill Wi
Points: 2040 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Lon(MN) Quote  Post ReplyReply Direct Link To This Post Posted: 12 Nov 2019 at 7:53am
After you separate the steering shaft, remove the two bolts on the rear of the bolster, you can then rotate the shaft out of the bolster. The rest of the gears and bearings will come out the bottom. All the bolts top and bottom need to come out.
Back to Top
Jareddrew82 View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 21 Oct 2019
Location: Missouri
Points: 13 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Jareddrew82 Quote  Post ReplyReply Direct Link To This Post Posted: 12 Nov 2019 at 5:16pm
Thanks for all the inputs! I got it
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.055 seconds.


Help Support the
Unofficial Allis Forum