| Author |
 Topic Search  Topic Options
|
Jake79 
Bronze Level
Joined: 13 May 2019
Location: Indiana
Points: 17
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: D19 3pt lift capacity
Posted: 12 Sep 2019 at 8:09pm |
|
I have looked through manual on lift capacity for tractor but had no luck. If anyone has any input I appreciate it.
|
 |
|
Sponsored Links
|
|
|
IBWD MIke
Orange Level
Joined: 08 Apr 2012
Location: Newton Ia.
Points: 4009
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Sep 2019 at 9:30am |
|
Looked on tractordata.com, didn't find an answer to your question. Thought we had a similar topic not too long ago?
|
|
CAL(KS)
Orange Level
Joined: 18 Sep 2009
Location: Chapman, KS
Points: 3800
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Sep 2019 at 9:44am |
|
between D17 and 190 if you can find those stats
|
|
Me -C,U,UC,WC,WD45,190XT,TL-12,145T,HD6G,HD16,HD20
Dad- WD, D17D, D19D, RT100A, 7020, 7080,7580, 2-8550's, 2-S77, HD15
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 21537
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Sep 2019 at 9:48am |
|
There were no published lift specs. Let's reverse the question. What are you trying to do?? A large round bale of hay shouldn't be a problem.
|
|
Gatz in NE
Orange Level
Joined: 11 Sep 2009
Location: Lincoln, NE
Points: 1043
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Sep 2019 at 10:18am |
^ that's surprising AC had the spec when designing the system; odd that they did not publish it. Were other tractor companies the same?
Our D17 had capacity enough to lift the whole (wide) front end. I'm sure the D19 would be similar, but it would be difficult to ascertain any valid number based on that capability because of the complicated geometry.
A guy could mount a 3pt carrier and keep adding weights until it would not lift anymore.
Edited by Gatz in NE - 13 Sep 2019 at 10:19am
|
|
Jake79
Bronze Level
Joined: 13 May 2019
Location: Indiana
Points: 17
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Sep 2019 at 10:23am |
|
Thanks for answering. Yes I cannot find anything either anyplace. #1400 disc mower is the thing I'm concerned about.
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 21537
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Sep 2019 at 10:26am |
|
If the hydraulic system is in good condition, it shouldn't be a problem. A 4 x 16's fully mounted 80 series plow weighed 1385 lbs.
|
|
frnkeore
Silver Level
Joined: 07 May 2019
Location: Southern Oregon
Points: 362
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Sep 2019 at 11:48am |
|
I can't say what a D19 will lift but, the following is what I found on what the different hitch capacity's are.
At 24" (61.0 cm) back from implement’s lower 3-point hitch pins.
Cat 0, 700 lbs (317.5 kg)
Cat I, 2000 lbs (907.2 kg)
Cat II, 3600 lbs (1632.9 kg)
Cat III, 13600 lbs (6168.9 kg)
|
|
Frank
1959 D17 Series I #24001+, '59 D14
'55 & '59 Ford 850 & 861
Ferguson TO 35 Deluxe, Oliver 70 and 5 more.
|
|
7060
Orange Level
Joined: 16 Sep 2009
Location: Missouri
Points: 1148
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Sep 2019 at 12:02pm |
|
My D17 will lift my Allis 4-16 fully mounted 3 point plow. If it is the same weight as your disc mower I wouldn’t think it would have any problem. I think I would want wheel weights or fluid in the left tire though.
|
|
allisbred
Orange Level Access
Joined: 28 Mar 2015
Location: Hanover Pa
Points: 1011
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Sep 2019 at 1:07pm |
|
The 3600# max weight sounds about right, we blew the seals at 3850# repetitive lifting on a 185.
|
|
Dakota Dave
Orange Level
Joined: 12 Sep 2009
Location: ND
Points: 3968
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Sep 2019 at 2:33pm |
|
My 190 would not lift a pallet with 4000 lbs of steel on it it did however lift the front end off the ground. With my 350 lb brother on the front end I was able to move the pallet 30 ft with it just barely touching the ground.
|
|
