This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


#7 rake parts needed
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
acjwb View Drop Down
Silver Level
Silver Level


Joined: 28 Oct 2009
Location: WV
Points: 309 		Post Options Post Options   Thanks (0) Thanks(0)   Quote acjwb Quote  Post ReplyReply Direct Link To This Post Topic: #7 rake parts needed
    Posted: 27 Nov 2018 at 7:33pm
   I am needing the pto shaft for a #7 hay rake. I have the back part that attaches to the rake gearbox. Thanks for any help.
Back to Top
Sponsored Links


Back to Top
PaulB View Drop Down
Orange Level
Orange Level


Joined: 12 Sep 2009
Location: Rocky Ridge Md
Points: 5157 		Post Options Post Options   Thanks (0) Thanks(0)   Quote PaulB Quote  Post ReplyReply Direct Link To This Post Posted: 28 Nov 2018 at 4:17am
I have some of those parts available, NOS. I’ll take a look to see which PTO parts I have later after I get home.
If it was fun to pull in LOW gear, I could have a John Deere.
Real pullers don't have speed limits.
If you can't make it GO... make it SHINY
Back to Top
B26240 View Drop Down
Orange Level
Orange Level


Joined: 21 Nov 2009
Location: mn
Points: 3866 		Post Options Post Options   Thanks (0) Thanks(0)   Quote B26240 Quote  Post ReplyReply Direct Link To This Post Posted: 28 Nov 2018 at 6:16am
I have the gearbox but no pto shafts.
Back to Top
PaulB View Drop Down
Orange Level
Orange Level


Joined: 12 Sep 2009
Location: Rocky Ridge Md
Points: 5157 		Post Options Post Options   Thanks (0) Thanks(0)   Quote PaulB Quote  Post ReplyReply Direct Link To This Post Posted: 28 Nov 2018 at 4:54pm
I have the front section of the rear driveshaft.  Part # 525569. This is the hollow square tube that has the area for the carrier bearing and then the yoke goes on in front of that. I have a picture although it doesn't want to show up. I sent you and Email.
If it was fun to pull in LOW gear, I could have a John Deere.
Real pullers don't have speed limits.
If you can't make it GO... make it SHINY
Back to Top
thomas winchester View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 05 May 2020
Location: richburg s.c.
Points: 1 		Post Options Post Options   Thanks (0) Thanks(0)   Quote thomas winchester Quote  Post ReplyReply Direct Link To This Post Posted: 05 May 2020 at 3:34pm
is it for sale
Back to Top
PaulB View Drop Down
Orange Level
Orange Level


Joined: 12 Sep 2009
Location: Rocky Ridge Md
Points: 5157 		Post Options Post Options   Thanks (0) Thanks(0)   Quote PaulB Quote  Post ReplyReply Direct Link To This Post Posted: 05 May 2020 at 8:21pm
Originally posted by thomas winchester thomas winchester wrote:

is it for sale

All of my NOS and used rake parts Went wit my rake when I sold it.  
If it was fun to pull in LOW gear, I could have a John Deere.
Real pullers don't have speed limits.
If you can't make it GO... make it SHINY
Back to Top
BSG View Drop Down
Bronze Level
Bronze Level


Joined: 30 Jul 2025
Location: Iowa
Points: 1 		Post Options Post Options   Thanks (0) Thanks(0)   Quote BSG Quote  Post ReplyReply Direct Link To This Post Posted: 30 Jul 2025 at 7:01pm
Im in need of a spocket for the main drive of a NO 7 rake.. Part number 517828.  a 36tooth #60 chain with 1 1/8" hub.
Back to Top
DanielW View Drop Down
Silver Level
Silver Level


Joined: 19 Sep 2022
Location: Ontario
Points: 240 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DanielW Quote  Post ReplyReply Direct Link To This Post Posted: 31 Jul 2025 at 6:47am
One of mine needed a new sprocket - I just went to the local Napa (which also serves as an industrial supply) and had them order one for me. Any industrial supply worth their salt will place regular orders to suppliers like Martin or Browning, who would have one in-stock. If this were a couple of weeks ago I might have had one to ship to you. But I just sold the three of those rakes I have with all the spare parts I had kicking around. Video link here explains tooth and bearing sourcing in case you ever need any of them.



Edited by DanielW - 31 Jul 2025 at 6:48am
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.070 seconds.


Help Support the
Unofficial Allis Forum