| Author |
 Topic Search  Topic Options
|
crich 
Bronze Level
Joined: 20 May 2014
Location: Ohio
Points: 11
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: Radiator hose
Posted: 02 Jun 2016 at 6:01pm |
|
I'm embarrassed just posting this issue. I had my water pump re-built so I thought it would be a good idea to replace the bottom hose, 1-1/2" hose. I have tried two worm drive type hose clamps turned 180 degress from each other, T bolt clamp with a worm drive clamps and it still leaks. I sanded and filed the stub coming off the bottom of the water pump and tried gasket sealer, and I must of broken 5 worm drive clamps trying to get it tight enough. I'm at my wits end, any ideas I haven't thought of ? I was thinking the radiator hose I'm using is a little stiffer than the one I replaced? Thanks for any ideas. Clinton
|
 |
|
Sponsored Links
|
|
|
crich
Bronze Level
Joined: 20 May 2014
Location: Ohio
Points: 11
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 Jun 2016 at 6:06pm |
|
BTW- I've researched new hoses on websites that have an I.D. dimension anywhere from 1.485"-1.158. Is that too little difference? Clinton
|
|
JPG AUSTRALIA
Orange Level
Joined: 13 Sep 2009
Points: 760
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 Jun 2016 at 6:38pm |
|
Just a thought ,its not your rebuilt pump leaking out the seal and running down your hose?
|
|
crich
Bronze Level
Joined: 20 May 2014
Location: Ohio
Points: 11
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 Jun 2016 at 6:47pm |
|
No, that was the first thing I checked. Clinton
|
|
Sugarmaker
Orange Level
Joined: 12 Jul 2013
Location: Albion PA
Points: 8429
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 Jun 2016 at 9:13pm |
|
It may get better after a year. Mine did! Guess it has to rust the hose back onto the pump!:)
Regards,
Chris
|
|
D17 1958 (NFE), WD45 1954 (NFE), WD 1952 (NFE), WD 1950 (WFE), Allis F-40 forklift, Allis CA, Allis D14, Ford Jubilee, Many IH Cub Cadets, 32 Ford Dump, 65 Comet.
|
|
MACK
Orange Level
Joined: 17 Nov 2009
Points: 7664
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 Jun 2016 at 9:53pm |
|
I agree with JPG AUSTRALIA. Water pump leaks. MACK
|
|
Bill_MN
Orange Level
Joined: 12 Sep 2009
Location: Sioux Falls, SD
Points: 1466
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Jun 2016 at 8:16pm |
|
How tight is the hose without a clamp? Those stiff radiator hoses don't just compress under the clamp they usually wrinkle up leaving a gap if they're much bigger than the pipe outlet. Get an OEM hose for your tractor that fits fairly tight or even stretches a bit without a clamp and line the inside where it seals with water pump and thermostat sealant, it will not leak guaranteed.
Edited by Bill_MN - 04 Jun 2016 at 8:17pm
|
|
1951 WD #78283, 1918 Case 28x50 Thresher #76738, Case Centennial B 2x16 Plow
|
|
DSeries4
Orange Level
Joined: 12 Sep 2009
Location: Ontario, Canada
Points: 7438
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Jun 2016 at 10:51pm |
 Bill_MN wrote:
How tight is the hose without a clamp? Those stiff radiator hoses don't just compress under the clamp they usually wrinkle up leaving a gap if they're much bigger than the pipe outlet. Get an OEM hose for your tractor that fits fairly tight or even stretches a bit without a clamp and line the inside where it seals with water pump and thermostat sealant, it will not leak guaranteed.
|
Exactly!
|
|
'49 G, '54 WD45, '55 CA, '56 WD45D, '57 WD45, '58 D14, '59 D14, '60 D14, '61 D15D, '66 D15II, '66 D21II, '67 D17IV, '67 D17IVD, '67 190XTD, '73 620, '76 185, '77 175, '84 8030, '85 6080
|
|
SHAMELESS
Orange Level
Joined: 13 Sep 2009
Location: EAST NE
Points: 29486
|
Post Options
Thanks(0)
Quote Reply
Posted: 05 Jun 2016 at 1:00am |
|
if you really think it's the hose, then get a bit smaller hose, pull the tractor up to the house, put the hose in the microwave for a little bit, (this will soften it), run out the door and slide it on and let it cool by itself. it should shrink down tight as it cools, then snug up a hose clamp to it. chances are it'll still be leaking out the water pump!
|
|
Fred in Pa
Orange Level
Joined: 13 Sep 2009
Location: Hanover Pa.
Points: 9210
|
Post Options
Thanks(0)
Quote Reply
Posted: 05 Jun 2016 at 3:09pm |
|
Someone drinking bathwater again Shameless !!!
|
|
He who dies with the most toys is,
nonetheless ,still dead.
If all else fails ,Read all that is PRINTED.
|
|
crich
Bronze Level
Joined: 20 May 2014
Location: Ohio
Points: 11
|
Post Options
Thanks(0)
Quote Reply
Posted: 05 Jun 2016 at 4:56pm |
|
I ordered a OEM hose, and clamps. I like the microwave idea. The hose should be in next week. I just had the water pump rebuilt, and I can see where the hose is leaking, before I even start the tractor, here's hoping it's not the water pump! Thanks! Clinton
|
|
SHAMELESS
Orange Level
Joined: 13 Sep 2009
Location: EAST NE
Points: 29486
|
Post Options
Thanks(0)
Quote Reply
Posted: 05 Jun 2016 at 6:09pm |
|
Fred...I've done that for years...works great with sprayer hoses too! don't always hafta do it that way, but sure is handy when you do!
|
|
WF owner
Orange Level
Joined: 12 May 2013
Location: Bombay NY
Points: 4889
|
Post Options
Thanks(0)
Quote Reply
Posted: 05 Jun 2016 at 6:44pm |
|
Hot water works to soften...and a little dish soap makes them slide on easier.
|
|
Ray54
Orange Level Access
Joined: 22 Nov 2009
Location: Paso Robles, Ca
Points: 4663
|
Post Options
Thanks(0)
Quote Reply
Posted: 05 Jun 2016 at 7:09pm |
|
For shameless people only!!!! Hold hose in exhaust pipe of a warmed up machine,can be done in any old field.I get little done now,if I took everything home to micro wave I would never get anything done.
|
|
SHAMELESS
Orange Level
Joined: 13 Sep 2009
Location: EAST NE
Points: 29486
|
Post Options
Thanks(0)
Quote Reply
Posted: 05 Jun 2016 at 9:49pm |
|
I gots a nuke machine in my shop, used just for stuff like this! it's the old one from the house after the old lady....ooops....I mean the loving wife decided we needed a newer/bigger one!
|
|
Bill_MN
Orange Level
Joined: 12 Sep 2009
Location: Sioux Falls, SD
Points: 1466
|
Post Options
Thanks(0)
Quote Reply
Posted: 06 Jun 2016 at 2:25pm |
|
shameless ya ever throw in a hot pocket with your rad hose?? hehehe
|
|
1951 WD #78283, 1918 Case 28x50 Thresher #76738, Case Centennial B 2x16 Plow
|
|
CTuckerNWIL
Orange Level
Joined: 11 Sep 2009
Location: NW Illinois
Points: 22822
|
Post Options
Thanks(0)
Quote Reply
Posted: 06 Jun 2016 at 5:22pm |
If the hose slides over the pipe easy, it might not seal up for some time. Get one that won't quite fit. If you put a cup of cooking oil in the microwave and get it hot, then dip the hose in the oil, it will soften it and act as a lubricant too. I used the wife's temperature probe in the oil to get it hot enough when I had to put new seals on a hydraulic cylinder
Edited by CTuckerNWIL - 06 Jun 2016 at 5:24pm
|
|
|
|
