This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
Allis 6080 cork gaskets - retighten? And dipstick |
Post Reply |
Author | |
ssefick
Bronze Level Joined: 09 Feb 2022 Location: South Carolina Points: 126 |
Post Options
Thanks(0)
Posted: 25 Sep 2022 at 8:11pm |
I am finishing a rebuild that was started by someone else (they unfortunatly passed before all the work was done). I have been torquing bolts where oil has been leaking to spec.
Do the cork gaskets "seat", and require retorqing? Specifically the valve cover, oil pan, and front cover. I torqued all of these to spec., and most of the oil leaks stopped. I noticed a little oil around the pan while I was getting the stearing cylendar off. My question is should I keep retorqing these? Do cork gaskets "seat"? My second question is is there a good after market heat to add to this tractor to help cold starting. Oil dipstick heater, or something else? Just got some electricity near the machine. Thanks for the help! Thanks all!
|
|
Sponsored Links | |
MACK
Orange Level Joined: 17 Nov 2009 Points: 7664 |
Post Options
Thanks(0)
|
Must be a cheep gasket set. Only cork gasket is valve cover.
Get bolt set for 8000 series valve cover and torque once. MACK
|
|
ssefick
Bronze Level Joined: 09 Feb 2022 Location: South Carolina Points: 126 |
Post Options
Thanks(0)
|
Thanks Mack. I'll see what I can do. Any thoughts on cold cranking after market heater?
|
|
Mikez
Orange Level Access Joined: 16 Jan 2013 Location: Usa Points: 8182 |
Post Options
Thanks(0)
|
Can’t you get a factory style block heater
|
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 19698 |
Post Options
Thanks(0)
|
Factory block heater just above the starter. Look for the cord.
|
|
AC720Man
Orange Level Joined: 10 Oct 2016 Location: Shenandoah, Va Points: 4727 |
Post Options
Thanks(0)
|
Cord unplugs so it can be replaced, it may have been removed if your not seeing it.
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
ssefick
Bronze Level Joined: 09 Feb 2022 Location: South Carolina Points: 126 |
Post Options
Thanks(0)
|
I don't see the heater at all. Where would I get one of these?
|
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 19698 |
Post Options
Thanks(0)
|
It is located directly above the starter, a "cats-eye" shaped plate bolted to the engines block. It has a 1/2" tube welded to it that crosses over behind the block to the oil filter area on the other side. If there is no electrical connection on the cats-eye plate, you don't have a block heater. AGCO is the only place I know of to get one, if they still have them.
|
|
SteveM C/IL
Orange Level Access Joined: 12 Sep 2009 Location: Shelbyville IL Points: 8070 |
Post Options
Thanks(0)
|
It not priced in parts book. Think there was talk here while back NLA.
|
|
DougG
Orange Level Joined: 20 Sep 2009 Location: Mo Points: 7978 |
Post Options
Thanks(0)
|
Theres a place in PA- Country Side Tractor , or something like that- has a kit for this - or get one for the One Eighty, 190 , etc then drill out a passage toward the back and hose it to the oil cooler with fittings etc
Edited by DougG - 29 Sep 2022 at 6:56pm |
|
SteveM C/IL
Orange Level Access Joined: 12 Sep 2009 Location: Shelbyville IL Points: 8070 |
Post Options
Thanks(0)
|
Yes with some ingenuity you cake "make" one
|
|
ssefick
Bronze Level Joined: 09 Feb 2022 Location: South Carolina Points: 126 |
Post Options
Thanks(0)
|
Understood. I am talking to the folks in PA. See what we can figure out.
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |