This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


WD 45 pan gasket ?
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Larry Miller View Drop Down
Orange Level
Orange Level
Avatar

Joined: 21 Nov 2009
Location: NWIL
Points: 909 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Larry Miller Quote  Post ReplyReply Direct Link To This Post Topic: WD 45 pan gasket ?
    Posted: 30 Jul 2020 at 7:50pm
The pan gasket set has two little paper thin almost square w a notch. apx inch and half by inch and half. A not mechanical description is they look like a cow - legs down and head showing - the notch between the legs.
What do they do and where do they go?
Thanks, Larry Miller
I used to be young and stupid, now I am not young anymore.
Back to Top
Sponsored Links


Back to Top
den/southern illinoi View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: Sparta, Illinoi
Points: 2071 		Post Options Post Options   Thanks (0) Thanks(0)   Quote den/southern illinoi Quote  Post ReplyReply Direct Link To This Post Posted: 30 Jul 2020 at 8:14pm
If you go to the Knowledge section and find Don Bradley's video of how to correctly install the pan gasket, etc.  He will answer all your questions.   Den

Own 4 wheel 20, 2-5015, 5020 and associated equipment and 2 electric forklifts.
Back to Top
Larry Miller View Drop Down
Orange Level
Orange Level
Avatar

Joined: 21 Nov 2009
Location: NWIL
Points: 909 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Larry Miller Quote  Post ReplyReply Direct Link To This Post Posted: 30 Jul 2020 at 8:44pm
Thanks Den - I need to spend a week there.
I used to be young and stupid, now I am not young anymore.
Back to Top
Sugarmaker View Drop Down
Orange Level
Orange Level
Avatar

Joined: 12 Jul 2013
Location: Albion PA
Points: 8534 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Sugarmaker Quote  Post ReplyReply Direct Link To This Post Posted: 30 Jul 2020 at 9:07pm
Larry,
 I may be wrong but I believe your talking about the "F" gaskets? They go near the rear main on the aluminum rear seal plate I believe. 
Regards,
 Chris
D17 1958 (NFE), WD45 1954 (NFE), WD 1952 (NFE), WD 1950 (WFE), Allis F-40 forklift, Allis CA, Allis D14, Ford Jubilee, Many IH Cub Cadets, 32 Ford Dump, 65 Comet.
Back to Top
Larry Miller View Drop Down
Orange Level
Orange Level
Avatar

Joined: 21 Nov 2009
Location: NWIL
Points: 909 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Larry Miller Quote  Post ReplyReply Direct Link To This Post Posted: 30 Jul 2020 at 9:25pm
You are right Sugarmaker - I had to come back and change those cow thingies to "F" gaskets.
Great video - I will go to the knowledge section before asking these kinds of questions again. Thanks again.
I used to be young and stupid, now I am not young anymore.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.094 seconds.


Help Support the
Unofficial Allis Forum