This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Allis G - N62 Oil Filter Mount
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
K-Mo View Drop Down
Bronze Level
Bronze Level


Joined: 09 Feb 2013
Location: Atlantic, IA
Points: 91 		Post Options Post Options   Thanks (0) Thanks(0)   Quote K-Mo Quote  Post ReplyReply Direct Link To This Post Topic: Allis G - N62 Oil Filter Mount
    Posted: 28 Sep 2016 at 10:33am
New to Allis G. The oil filter mount is not tight in the block. I don't find any method to secure it. Is it just a press fit into the block? Has anyone had this situation and if so, what would be a good solution?
I think JB Weld may be a little to permanent in case the mount broke and had to be replaced.
Thanks,
Kent


Edited by K-Mo - 28 Sep 2016 at 10:38am
Back to Top
Sponsored Links


Back to Top
JoeM(GA) View Drop Down
Orange Level
Orange Level
Avatar

Joined: 12 Sep 2009
Location: Cumming,GA
Points: 4760 		Post Options Post Options   Thanks (0) Thanks(0)   Quote JoeM(GA) Quote  Post ReplyReply Direct Link To This Post Posted: 28 Sep 2016 at 10:49am
Go ahead and pull it out, stake it with a punch all the way around, then re-set it in the hole with a mallet and a wood block. It should be fine, you could also set it with some green loctite, but get it where you want it before it sets.
Allis Express North Georgia
41 WC,48 UC Cane,7-G's,
Ford 345C TLB
Back to Top
K-Mo View Drop Down
Bronze Level
Bronze Level


Joined: 09 Feb 2013
Location: Atlantic, IA
Points: 91 		Post Options Post Options   Thanks (0) Thanks(0)   Quote K-Mo Quote  Post ReplyReply Direct Link To This Post Posted: 28 Sep 2016 at 12:40pm
Good suggestions. I like the Loctite idea. I'll check the specs on the green. If I remember correctly some Loctite formulas can be loosened with a specified amount of heat.
I think the oil filter mount is pot metal. It would be my luck to break it while trying to use a punch on it and drive it into place.
Thanks
 
Back to Top
JoeM(GA) View Drop Down
Orange Level
Orange Level
Avatar

Joined: 12 Sep 2009
Location: Cumming,GA
Points: 4760 		Post Options Post Options   Thanks (0) Thanks(0)   Quote JoeM(GA) Quote  Post ReplyReply Direct Link To This Post Posted: 28 Sep 2016 at 1:12pm
you don't have to hit it hard, you're just trying to give it some bite in the hole
Allis Express North Georgia
41 WC,48 UC Cane,7-G's,
Ford 345C TLB
Back to Top
Fred in Pa View Drop Down
Orange Level
Orange Level
Avatar

Joined: 13 Sep 2009
Location: Hanover Pa.
Points: 9210 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Fred in Pa Quote  Post ReplyReply Direct Link To This Post Posted: 28 Sep 2016 at 1:28pm


Don't use the Loctite ,get the Right Stuff ,it will seal it and help hold it .Still stake it
He who dies with the most toys is,
nonetheless ,still dead.
If all else fails ,Read all that is PRINTED.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.129 seconds.


Help Support the
Unofficial Allis Forum