![]() |
This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | |||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
9690 error code ??? |
Post Reply ![]() |
Author | |
Mark D. ![]() Silver Level Access ![]() ![]() Joined: 14 Sep 2009 Location: Ubly, MI Points: 215 |
![]() ![]() ![]() ![]() ![]() Posted: 19 Oct 2011 at 2:27pm |
Getting e 0 1 code, doesn't pull in factor 3 gears (6, 9, 15, 18 etc.). Changed cylinoid but doesn't help. Any and all help/suggestions would be appreciated.
|
|
Miss Behavin - D21 Super Farm
Xcessive Tinkering - 190 XT Hot Farm Puller Watch on YouTube - http://www.youtube.com/watch?v=J2TX1Af7aoA |
|
![]() |
|
Sponsored Links | |
![]() |
|
frankmi ![]() Silver Level ![]() Joined: 11 Sep 2009 Location: michigan Points: 52 |
![]() ![]() ![]() ![]() ![]() |
I HAVE A 9655 that did almost the same thing. Found out that the problem was the electric plug in in the cab to the out side of the cab had bad connection (corrosion). Two cables in, two cables out. Not sure which cable handles trans. opperations, but if you can unplug and replug this may show if this is the problem. On my 9655 they are located on lower left corner of cab, not real easy to get too! FrankMI.
|
|
![]() |
|
ncrc5315 ![]() Silver Level ![]() Joined: 10 Sep 2010 Location: Nebraska Points: 68 |
![]() ![]() ![]() ![]() ![]() |
How do you like the 9690?
|
|
![]() |
|
MACK ![]() Orange Level ![]() Joined: 17 Nov 2009 Points: 7664 |
![]() ![]() ![]() ![]() ![]() |
Check the ground on left side inside cab door on trans housing. Take the bolt out clean every thing good, and use antiseze or something to keep it from rusting or a good conducter. MACK
|
|
![]() |
|
Mark D. ![]() Silver Level Access ![]() ![]() Joined: 14 Sep 2009 Location: Ubly, MI Points: 215 |
![]() ![]() ![]() ![]() ![]() |
Thought that we would end up looking to the firewall plug. We have already made a jump wire for that plug which we use when the key will not roll the motor over.
We love the 9690!! Also have an JD 8330 and when it comes to doing the grunt work we use the orange one. It will out pull the JD in all conditions (especially wet) and do it more efficiently too!! Thats why we need to keep the 9690 going. Thanks!!!
|
|
Miss Behavin - D21 Super Farm
Xcessive Tinkering - 190 XT Hot Farm Puller Watch on YouTube - http://www.youtube.com/watch?v=J2TX1Af7aoA |
|
![]() |
|
Mark D. ![]() Silver Level Access ![]() ![]() Joined: 14 Sep 2009 Location: Ubly, MI Points: 215 |
![]() ![]() ![]() ![]() ![]() |
Ran all the tests we could before asking for a service call. Card Bros. out of MI is a great resource. They came out and replaced the computer which controls the transmission and we are back up and running. Now if it just stopped raining long enough to get harvest and fall work done!! Thanks guys!!
|
|
Miss Behavin - D21 Super Farm
Xcessive Tinkering - 190 XT Hot Farm Puller Watch on YouTube - http://www.youtube.com/watch?v=J2TX1Af7aoA |
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |