226 260 cid setup

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

I have a cheap and easy parts setup I'd like to sell for someone looking to do a little upgradeing without breaking the bank or working to hard to do it.  
Set of 4 IH 308 truck engine rods, 4.185 bore Keith Black KB194 .060 over pistons and rings.  2 pistons brand new, 2 slightly used (neighbor had bought 8 and had 6 of them in his 6 cyl tractor engine for a bit) 

Works out to bore a set of 4 1/8 bore liners .060 over and offset grind the 4.5 stroke crankshaft to a 4.75 stroke.  You get a 4.185 bore X 4.75 stroke engine at 10.5 to 1 compression ratio. 

The rods are 8.5625" long center to center,  use a 2.125" diameter crankpin and are wide enough to fit the Allis crankpin.  The wrist pins in the IH are .925" and the pistons are .927".  I have honed the wrist pin bushings to size and resized the bottom end of the rods so they are ready to go.

$300 for the rods, pistons, rings, wrist pins and new spriol locks shipped to you.  

I do have nice used 4 1/8 liners available at additional cost, but I'd prefer to keep them.  Approxamate cost to bore and hone the liners is $100-$125, offset grind the 4 cyl crank $250.

	This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
	The Forum	Parts and Services	Unofficial Allis Store	Tractor Shows	Serial Numbers	History

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
wi50 Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Joined: 24 Sep 2010 Location: weegieland Points: 1010	Post Options Post Reply Quote wi50 Report Post Thanks(0) Quote Reply Topic: 226 260 cid setup Posted: 17 Jan 2013 at 9:16pm
	I have a cheap and easy parts setup I'd like to sell for someone looking to do a little upgradeing without breaking the bank or working to hard to do it. Set of 4 IH 308 truck engine rods, 4.185 bore Keith Black KB194 .060 over pistons and rings. 2 pistons brand new, 2 slightly used (neighbor had bought 8 and had 6 of them in his 6 cyl tractor engine for a bit) Works out to bore a set of 4 1/8 bore liners .060 over and offset grind the 4.5 stroke crankshaft to a 4.75 stroke. You get a 4.185 bore X 4.75 stroke engine at 10.5 to 1 compression ratio. The rods are 8.5625" long center to center, use a 2.125" diameter crankpin and are wide enough to fit the Allis crankpin. The wrist pins in the IH are .925" and the pistons are .927". I have honed the wrist pin bushings to size and resized the bottom end of the rods so they are ready to go. $300 for the rods, pistons, rings, wrist pins and new spriol locks shipped to you. I do have nice used 4 1/8 liners available at additional cost, but I'd prefer to keep them. Approxamate cost to bore and hone the liners is $100-$125, offset grind the 4 cyl crank $250.
	"see what happens when you have no practical experience doing something...... you end up playing with calculators and looking stupid on the internet"

Sponsored Links

Charlie175 Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Joined: 11 Sep 2009 Location: Shenandoah, VA Points: 6351	Post Options Post Reply Quote Charlie175 Report Post Thanks(0) Quote Reply Posted: 18 Jan 2013 at 6:25am
	what kind of power output would this give?
	Charlie '48 B, '51 CA, '56 WD45 '61 D17, '63 D12, '65 D10 , '68 One-Ninety XTD

nborga87 Members Profile Send Private Message Find Members Posts Add to Buddy List Silver Level Joined: 08 Jun 2010 Location: cordova, md Points: 115	Post Options Post Reply Quote nborga87 Report Post Thanks(0) Quote Reply Posted: 29 Mar 2013 at 12:14am
	do you still have these parts?

wi50 Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Joined: 24 Sep 2010 Location: weegieland Points: 1010	Post Options Post Reply Quote wi50 Report Post Thanks(0) Quote Reply Posted: 29 Mar 2013 at 12:47pm
	Yes, I still have them, allong with bored sleves with new o-rings. Also a 5.75 stroke crank and 8" billet rods for another combo. 715-790-1869
	"see what happens when you have no practical experience doing something...... you end up playing with calculators and looking stupid on the internet"