This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Other Topics > Shops, Barns, Varmints, and Trucks
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Getting the Meatgrinder Back in Service
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Dave H View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: Central IL
Points: 3598 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Dave H Quote  Post ReplyReply Direct Link To This Post Topic: Getting the Meatgrinder Back in Service
    Posted: 23 hours 42 minutes ago at 5:12pm
I just acquired an Enterprise meat grinder today.  A great snag for the price with V belt pulley.  This thing has been laying collecting gunge, some rust, and nastiness.  So I plan on hitting most of it lightly with a wire wheel.

What do you recommend for a protective coating after clean up.  It would be nice to spray some type of oil (vegetable) on iit and hit that with the air gun.

What would be your suggestion.  Oh and how to clean up the plates with holes in them?  thanx
Back to Top
Sponsored Links


Back to Top
steve(ill) View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 11 Sep 2009
Location: illinois
Points: 89705 		Post Options Post Options   Thanks (0) Thanks(0)   Quote steve(ill) Quote  Post ReplyReply Direct Link To This Post Posted: 23 hours 25 minutes ago at 5:29pm
if it is mostly CRUD... I would spray with oven cleaner, let it set for 30 minutes, then wash off with soap and water and scrub brush... For the rust, i would use the sand blaster.. without that, the wire brush sounds good...

i have never tried this stuff, but many brag about it...




Edited by steve(ill) - 23 hours 22 minutes ago at 5:32pm
Like them all, but love the "B"s.
Back to Top
Hubert (Ga)engine7 View Drop Down
Orange Level
Orange Level
Avatar

Joined: 12 Sep 2009
Location: Jackson Cnty,GA
Points: 6574 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Hubert (Ga)engine7 Quote  Post ReplyReply Direct Link To This Post Posted: 20 hours 46 minutes ago at 8:08pm
I would avoid harsh chemicals if at all possible when removing the gunk and rust. Also avoid vegetable oil, that could be the cause of your gunk. You might have to use a drill bit that is just under the size of the holes in the plate to get the gunk out of it. Keep in mind that the side of the plate that contacts the knife perfectly flat and square to work properly. I wash all of my grinder parts with hot soapy water immediately after use, dry everything and then spray everything with food grade silicone based lubricant. If you store it disassembled wrap the knife and plate(s) in a cloth saturated with the spray and place in a ziplock bag. When you reassemble use some food grade grease as needed. M

Edited by Hubert (Ga)engine7 - 20 hours 40 minutes ago at 8:14pm
Just an old country boy saved by the grace of God.
Back to Top
Dirt Farmer View Drop Down
Silver Level Access
Silver Level Access


Joined: 15 Sep 2020
Location: Illinois
Points: 456 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Dirt Farmer Quote  Post ReplyReply Direct Link To This Post Posted: 19 hours 46 minutes ago at 9:08pm
I would avoid oven cleaner as some of the parts may be aluminum and they could become discolored. I would opt for a wash down with a pressure washer with substantial heat and probably wouldn’t need soap or if did use dawn dish soap. Never done one but this is my simple go to for cleaning things like my gas grill
Back to Top
Dave H View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: Central IL
Points: 3598 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Dave H Quote  Post ReplyReply Direct Link To This Post Posted: 3 hours 15 minutes ago at 1:39pm
thanks for the infp folks.  Hubert, you covered all the bases.

Maybe after it thaws out a bit, she will be brought back into service for the next round of venison,  Big smile
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.047 seconds.


Help Support the
Unofficial Allis Forum