| Author |
 Topic Search  Topic Options
|
dfwallis 
Orange Level
Joined: 09 Mar 2023
Location: DFW
Points: 669
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: CA PTO Shear Bolt/Shaft Direction
Posted: 30 Apr 2025 at 1:07pm |
New mower has label pointing the end with the shear bolt toward the tractor. There are two issues with this:'
1) The shear bolt is on a 1.5"+ protrusion off to the side of the Ujoint and nearly hits the top link bracket attached to the rock shaft.
2) This would cause water to run into the PTO shaft because the open end of the sheath would be pointed upward.
I intend to mount it in the other direction because there is plenty of room for the shear bolt protrusion on the implement, and I want the sheath pointed downward to preclude water intrusion. I also may install my new slip clutch on the implement if the geometry/length works. There's no way the slip clutch would clear the rockshaft attached top link bracket.
Issues?
|
|
1952 CA13092
|
 |
|
Sponsored Links
|
|
|
Jim.ME
Orange Level
Joined: 19 Nov 2016
Location: Maine
Points: 959
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 hours 59 minutes ago at 5:32pm |
A slip clutch belongs on the implement, not the tractor PTO shaft. An over-running clutch goes on the tractor's PTO shaft.
With a slip clutch you don't need the shear bolt set up.
|
|
steve(ill)
Orange Level Access
Joined: 11 Sep 2009
Location: illinois
Points: 85654
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 hours 43 minutes ago at 5:48pm |
|
we alway put the shear bolt on the mower deck end.... many mowers have the gear box INPUT shaft as ROUND with the bolt thru it... not a HEX drive like the tractor PTO.
Edited by steve(ill) - 11 hours 42 minutes ago at 5:49pm
|
|
Like them all, but love the "B"s.
|
|
dfwallis
Orange Level
Joined: 09 Mar 2023
Location: DFW
Points: 669
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 hours 12 minutes ago at 7:19pm |
 Jim.ME wrote:
A slip clutch belongs on the implement, not the tractor PTO shaft. An over-running clutch goes on the tractor's PTO shaft.
With a slip clutch you don't need the shear bolt set up. |
That's where I intend to install it. The PTO shaft itself already came with a shear bolt and markings indicate to attach it to the tractor. But I thought that was not the best approach, and not suitable for a 3 point modded CA.
|
|
1952 CA13092
|
|
dfwallis
Orange Level
Joined: 09 Mar 2023
Location: DFW
Points: 669
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 hours 11 minutes ago at 7:20pm |
steve(ill) wrote:
we alway put the shear bolt on the mower deck end.... many mowers have the gear box INPUT shaft as ROUND with the bolt thru it... not a HEX drive like the tractor PTO. |
Thanks, This one has a normal 1 3/8 PTO 6 spline on the implement.
|
|
1952 CA13092
|
|
dfwallis
Orange Level
Joined: 09 Mar 2023
Location: DFW
Points: 669
|
Post Options
Thanks(0)
Quote Reply
Posted: 8 hours 54 minutes ago at 8:37pm |
|
I'm thinking I may just turn the shroud around if I ever have to modify it (shorten, etc.) so other's (brothers, nephews, etc.) don't install it with the shear bolt toward the tractor.
|
|
1952 CA13092
|
|
DiyDave
Orange Level Access
Joined: 11 Sep 2009
Location: Gambrills, MD
Points: 53302
|
Post Options
Thanks(1)
Quote Reply
Posted: 8 hours 48 minutes ago at 8:43pm |
dfwallis wrote:
I'm thinking I may just turn the shroud around if I ever have to modify it (shorten, etc.) so other's (brothers, nephews, etc.) don't install it with the shear bolt toward the tractor. |
Likely that's what happened at the factory, got it put together backwards... Don't operate it that way, or you'll un-mow your lawn...
|
|
Source: Babylon Bee. Sponsored by BRAWNDO, its got what you need!
|
|
