WD45 Governor issues...need help

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

    I have an Allis-Chalmers WD45 with the 226 engine. I have owned it only a few weeks and have driven it only a few times. 

I am worried about a governor problem, possibly broken governor weights, but I figured I'd ask the experts before I disassemble things. 

It's always seemed to have a slight hunting/surging RPM feel, along with a dead spot in the hand throttle.  One time I heard/felt the governor work normally while going up a hill: the engine loaded down and the governor slightly increased RPM's like it should.

 Now, usually under a light load and with the hand quadrant  around 1/4 throttle, it will:

 1. Start to stumble or lose RPM.
2. rapidly accelerate RPM (only for a second or so) 
3. It stumbles again.
 4. It stalls.

 After it stalls, I can get off and see that the governor has pulled the carburetor throttle plate all the way open, even though the hand throttle is only around 1/4 throttle.

 I can manually raise and lower RPM normally with the hand throttle at other times. The tractor starts right up, idles perfectly fine, will run fine at working RPM's,  but acts up about once every 3 or 4 minutes, always under light-moderate load. 
The linkages for the gov/carb/throttle are all decently tight, none of the connections are noticeably "sloppy" and the connector holes are nice and round. 

 I checked fuel flow to the carburetor and it appears fine.  I have not yet confirmed the condition of the carburetor internally, including float level, needle/seat, main jet/nozzle, passages, adjustment, or throttle-shaft wear, but the tractor starts and idles just fine. I was reading my owners manual, and it dosen't seem to say much regarding the governor and the proper adjustment procedure. My main concern was broken weights. Are broken weights likely, given the symptoms? I'm a decent shadetree mechanic but this is my first Allis so I'm learning as I go. Thanks y'all!

Edited by BossofBBQ - 1 hour 9 minutes ago at 3:07pm

	This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
	The Forum	Parts and Services	Unofficial Allis Store	Tractor Shows	Serial Numbers	History

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
BossofBBQ Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 24 Jul 2026 Location: Colorado Points: 10	Post Options Post Reply Quote BossofBBQ Report Post Thanks(0) Quote Reply Topic: WD45 Governor issues...need help Posted: 1 hour 16 minutes ago at 3:00pm
	I have an Allis-Chalmers WD45 with the 226 engine. I have owned it only a few weeks and have driven it only a few times. I am worried about a governor problem, possibly broken governor weights, but I figured I'd ask the experts before I disassemble things. It's always seemed to have a slight hunting/surging RPM feel, along with a dead spot in the hand throttle. One time I heard/felt the governor work normally while going up a hill: the engine loaded down and the governor slightly increased RPM's like it should. Now, usually under a light load and with the hand quadrant around 1/4 throttle, it will: 1. Start to stumble or lose RPM. 2. rapidly accelerate RPM (only for a second or so) 3. It stumbles again. 4. It stalls. After it stalls, I can get off and see that the governor has pulled the carburetor throttle plate all the way open, even though the hand throttle is only around 1/4 throttle. I can manually raise and lower RPM normally with the hand throttle at other times. The tractor starts right up, idles perfectly fine, will run fine at working RPM's, but acts up about once every 3 or 4 minutes, always under light-moderate load. The linkages for the gov/carb/throttle are all decently tight, none of the connections are noticeably "sloppy" and the connector holes are nice and round. I checked fuel flow to the carburetor and it appears fine. I have not yet confirmed the condition of the carburetor internally, including float level, needle/seat, main jet/nozzle, passages, adjustment, or throttle-shaft wear, but the tractor starts and idles just fine. I was reading my owners manual, and it dosen't seem to say much regarding the governor and the proper adjustment procedure. My main concern was broken weights. Are broken weights likely, given the symptoms? I'm a decent shadetree mechanic but this is my first Allis so I'm learning as I go. Thanks y'all! Edited by BossofBBQ - 1 hour 9 minutes ago at 3:07pm

Sponsored Links