| Author |
 Topic Search  Topic Options
|
Dkienzle 
Silver Level
Joined: 22 Feb 2013
Location: Central IA
Points: 204
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: 8050 muffler eliminator
Posted: 19 Sep 2026 at 9:25pm |
|
Is there anywhere that you can still find a muffler eliminater for a 8050? I think the company that used to make them closed, any other leads? Thanks
|
 |
|
Sponsored Links
|
|
|
NEVER green
Orange Level Access
Joined: 28 Feb 2013
Location: MN.
Points: 9795
|
Post Options
Thanks(0)
Quote Reply
Posted: Yesterday at 9:07am |
Had one threw it in the scrap, had outrageous 180 degree angle on it.
Are you looking for more flow?
Edited by NEVER green - 4 hours 13 minutes ago at 8:06am
|
|
2-8050 1-7080 6080 D-19 modelE & A 7040 R50
|
|
SteveM C/IL
Orange Level Access
Joined: 12 Sep 2009
Location: Shelbyville IL
Points: 9202
|
Post Options
Thanks(0)
Quote Reply
Posted: Yesterday at 10:43am |
|
was Thomure Mfg. Think some one took over some of their stuff but not sure. Mine has a section sliced welded 180 which is a little sharp and crude but ok. I never seen much difference on the pyrometer. Not enough noise difference in cab to notice. Have 2 8070's. One with and one without. The muffler one is quieter outside of cab but that's it.
|
|
Ricky38
Bronze Level
Joined: Yesterday
Location: NY
Points: 4
|
Post Options
Thanks(0)
Quote Reply
Posted: Yesterday at 11:56am |
|
Jim Kemp on the Wheel Horse forum is your guy. He builds custom stacks and eliminators. Or just have a local exhaust shop bend you a straight pipe.
|
|
ryan(IN)
Orange Level
Joined: 11 Sep 2009
Location: Bluffton,IN
Points: 805
|
Post Options
Thanks(0)
Quote Reply
Posted: 21 hours 26 minutes ago at 2:53pm |
|
I emailed Thomure this winter. he is still doing stuff just not as much as he was. I think he makes them to order or when he gets a couple to do. I would call and see. Thomure MFG
|
|
ryan
1984 8070 FWA,1979 7060,1975 7040,1971 190,1960 D-17D,1957 D-14, 196? D-19G, 1975 5040,1971? 160,1994 R62
|
|
Alvin M
Orange Level
Joined: 24 Jun 2018
Location: PA
Points: 855
|
Post Options
Thanks(0)
Quote Reply
Posted: 20 hours 10 minutes ago at 4:09pm |
|
Thomure Part # Is AC759ASP I Googled It Cam Up
|
|
SteveM C/IL
Orange Level Access
Joined: 12 Sep 2009
Location: Shelbyville IL
Points: 9202
|
Post Options
Thanks(0)
Quote Reply
Posted: 14 hours 31 minutes ago at 9:48pm |
 Ricky38 wrote:
Jim Kemp on the Wheel Horse forum is your guy. He builds custom stacks and eliminators. Or just have a local exhaust shop bend you a straight pipe. |
I don't think you can bend a straight pipe that tight.
|
|
8070nc
Orange Level Access
Joined: 21 Mar 2019
Location: North Carolina
Points: 902
|
Post Options
Thanks(0)
Quote Reply
Posted: 14 hours 27 minutes ago at 9:52pm |
|
Lift parts warehouse shiws to have them
|
|
1984 80780
1957 D14
DES 300 with 25000 engine
616 tractor
|
|
8070nc
Orange Level Access
Joined: 21 Mar 2019
Location: North Carolina
Points: 902
|
Post Options
Thanks(0)
Quote Reply
Posted: 14 hours 27 minutes ago at 9:52pm |
|
Shows
|
|
1984 80780
1957 D14
DES 300 with 25000 engine
616 tractor
|
|
NEVER green
Orange Level Access
Joined: 28 Feb 2013
Location: MN.
Points: 9795
|
Post Options
Thanks(0)
Quote Reply
Posted: 3 hours 51 minutes ago at 8:28am |
SteveM C/IL wrote:
was Thomure Mfg. Think some one took over some of their stuff but not sure. Mine has a section sliced welded 180 which is a little sharp and crude but ok. I never seen much difference on the pyrometer. Not enough noise difference in cab to notice. Have 2 8070's. One with and one without. The muffler one is quieter outside of cab but that's it. |
A little crude... it is terrible, a plumber would point and laugh at that. It aint no sweep elbow, the curve is not even round.
The muffler necks down from 4 inches to 2 inches in order to scavenge dust, also restrictive.
|
|
2-8050 1-7080 6080 D-19 modelE & A 7040 R50
|
|
SteveM C/IL
Orange Level Access
Joined: 12 Sep 2009
Location: Shelbyville IL
Points: 9202
|
Post Options
Thanks(0)
Quote Reply
Posted: 52 minutes ago at 11:27am |
|
Mine doesn't neck down. Has a horizontal asperator welded in outlet pipe. Have you looked at OEM muffler? Blows into rear chamber and has to find the outlet.
|
|
NEVER green
Orange Level Access
Joined: 28 Feb 2013
Location: MN.
Points: 9795
|
Post Options
Thanks(0)
Quote Reply
Posted: 21 minutes ago at 11:58am |
SteveM C/IL wrote:
Mine doesn't neck down. Has a horizontal asperator welded in outlet pipe. Have you looked at OEM muffler? Blows into rear chamber and has to find the outlet. |
Yes, I gutted one and it has more room to turn then that "thing", not great either but, air like water does not like sharp edges and short corners, that "thing " has both.
|
|
2-8050 1-7080 6080 D-19 modelE & A 7040 R50
|
|
