Paint Spray Gun Questions

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   My first time trying to paint with a HVLP spray gun and have a few questions:

About how many ounces of mixed paint does it take for for one coat on an Allis B (all parts are stripped)? The paint cup holds 34 ounces and I was thinking about mixing 24 ounces on first attempt.
If I end up with excess paint after the first coat, about how long will it keep in the spray gun before causing a problem?  I was planning a second coat in 40 to 60 minutes after the first (it’s about 70-80 degrees now during daytime high).
Using a hardener (Restoration Shop Enamel Wet Look Hardener). What are pros/cons of using this only on the final coat? Specs show to use 8 parts paint to 1 part hardener.
Plan to use an Airline Filter between two 50 foot long air hoses. Are these lengths okay, or should I get two much shorter air hoses?
I’m using custom mixed Industrial Automotive Enamel and plan to dilute 25% with paint thinner (internet searches note a range from 25% to 50%).  Is 25% a reasonable mix for a first attempt?

Using an ancient large stationary Peerless 1.5hp air compressor located in my tractor barn (plate does not disclose CFM).  I’m using a AllTrade Trades Pro HVLP gravity feed spray gun & cup with following specs on the large gun: Fluid Tip Dia 1.4mm, Air Consumption 11-13 CFM, Pressure 30-43 psi, Cup 34oz.

Thanks in advance for any help - Dale

	This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
	The Forum	Parts and Services	Unofficial Allis Store	Tractor Shows	Serial Numbers	History

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Dale (Stonelick) Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 13 Jun 2019 Location: Stonelick, Ohio Points: 184	Post Options Post Reply Quote Dale (Stonelick) Report Post Thanks(0) Quote Reply Topic: Paint Spray Gun Questions Posted: 2 hours 18 minutes ago at 5:44pm
	My first time trying to paint with a HVLP spray gun and have a few questions: About how many ounces of mixed paint does it take for for one coat on an Allis B (all parts are stripped)? The paint cup holds 34 ounces and I was thinking about mixing 24 ounces on first attempt. If I end up with excess paint after the first coat, about how long will it keep in the spray gun before causing a problem? I was planning a second coat in 40 to 60 minutes after the first (it’s about 70-80 degrees now during daytime high). Using a hardener (Restoration Shop Enamel Wet Look Hardener). What are pros/cons of using this only on the final coat? Specs show to use 8 parts paint to 1 part hardener. Plan to use an Airline Filter between two 50 foot long air hoses. Are these lengths okay, or should I get two much shorter air hoses? I’m using custom mixed Industrial Automotive Enamel and plan to dilute 25% with paint thinner (internet searches note a range from 25% to 50%). Is 25% a reasonable mix for a first attempt? Using an ancient large stationary Peerless 1.5hp air compressor located in my tractor barn (plate does not disclose CFM). I’m using a AllTrade Trades Pro HVLP gravity feed spray gun & cup with following specs on the large gun: Fluid Tip Dia 1.4mm, Air Consumption 11-13 CFM, Pressure 30-43 psi, Cup 34oz. Thanks in advance for any help - Dale
	1951 CA - 1944 C - 1949 B - Kubota M6800

Sponsored Links

Dirt Farmer Members Profile Send Private Message Find Members Posts Add to Buddy List Silver Level Access Joined: 15 Sep 2020 Location: Illinois Points: 439	Post Options Post Reply Quote Dirt Farmer Report Post Thanks(0) Quote Reply Posted: 1 hour 15 minutes ago at 6:47pm
	Don't know about the paint amount needed or if you will have enough air capacity, you didn't mention how big the tank is. I an addressing the inline filter, attach it as close to the gun as possible cause moisture is the enemy in painting and all can look great then all of a sudden there is a drip of water mixed in the paint and not much you can do with that spot at that moment. Put the filter between the gun pressure regulator and the hose connector. Practice and patience, put some thinner in the gun and try spraying that on cardboard to see if the air keeps up and look at the pattern the gun is spraying. Seek out a couple you tube videos to get an idea. Good luck and wear a face mask to protect your lungs