This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Construction and other equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


help on my h4
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
pinball View Drop Down
Orange Level Access
Orange Level Access


Joined: 28 May 2014
Location: missouriu
Points: 6380 		Post Options Post Options   Thanks (0) Thanks(0)   Quote pinball Quote  Post ReplyReply Direct Link To This Post Topic: help on my h4
    Posted: 17 Aug 2018 at 9:54pm
I have been working on replacing a seal on my right final drive. So I put on the new seal and seal protector, pressed the bearing completely on and inserted the outer spacer. put shaft through the bull gear and added the smaller spacer then the snap ring. put the inside bearing on and used the bolt to pull the shaft through and used spacers to drive in the seal and seal protector, then went in fine and are flush with the casing. the problem is I have not been able to get the inner snap ring in place. so my question is how and devil do I get it in place. sure would hate to half to take the case off to fix it as the book says it can be done while the case is in place. need some good advise fellows. thanks norm
Back to Top
Sponsored Links


Back to Top
Randaleky View Drop Down
Silver Level
Silver Level
Avatar

Joined: 17 Aug 2011
Location: belfry, ky.
Points: 427 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Randaleky Quote  Post ReplyReply Direct Link To This Post Posted: 17 Aug 2018 at 10:50pm
not quiet following you Norman. I looked at book and am thinking you are talking about the snap ring that holds the cap on ?
Back to Top
pinball View Drop Down
Orange Level Access
Orange Level Access


Joined: 28 May 2014
Location: missouriu
Points: 6380 		Post Options Post Options   Thanks (0) Thanks(0)   Quote pinball Quote  Post ReplyReply Direct Link To This Post Posted: 18 Aug 2018 at 6:45am
hello randall. its the inside snap ring. it holds the collar against the bull gear inside to keep it lined up. just very little room to get to it as you have to reach up between the bull gear nd case. I have ordered another snap ring pliers to see if that will work. one I have I can get into the snap ring but it keeps wanting to twist the snap ring. just thought some one on here had maybe done this before. thanks norm
Back to Top
Coke-in-MN View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 12 Sep 2009
Location: Afton MN
Points: 41979 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Coke-in-MN Quote  Post ReplyReply Direct Link To This Post Posted: 18 Aug 2018 at 9:27am
Failed memory of the operation prevents me from giving advice - I must have done that job several times as I replaced axles on the HD4 quite a few times seems with snap ring on axle it was just slid into place as the assembly progressed - only needed snap ring pliers to remove the full mess 
Life lesson: If you’re being chased by a lion, you’re on a horse, to the left of you is a giraffe and on the right is a unicorn, what do you do? You stop drinking and get off the carousel.
Back to Top
Randaleky View Drop Down
Silver Level
Silver Level
Avatar

Joined: 17 Aug 2011
Location: belfry, ky.
Points: 427 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Randaleky Quote  Post ReplyReply Direct Link To This Post Posted: 18 Aug 2018 at 3:23pm
I am with coke. I do not remember trouble with the snap ring Norman.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.032 seconds.


Help Support the
Unofficial Allis Forum