A GIGANTIC THANK YOU!!!
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=51604
Printed Date: 25 Aug 2025 at 3:50pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: A GIGANTIC THANK YOU!!!
Posted By: MilesGray (CO/KS)
Subject: A GIGANTIC THANK YOU!!!
Date Posted: 05 Jun 2012 at 6:24am
I just want to say a huge thank you to Steve Jelfs for helping me with my Tractor problems!!! I have learned a whole lot through this process and it's still not over, but the end is in sight! .It started with needing a clutch. When we split the tractor for that, the drive line came forward with the engine... so now it has been split at the rear and we put in a "new" shaft in the transmission because it had slipped when the cotter pin came out and ground off the splines on the "old" one. Luckily, I had a few I could choose from and I haven't had to buy any parts as of yet...------------- Miles Gray (CO/KS) 5 1938 B's, 1940 B, 1944 WF C, 1948 NF C, Gleaner A, White Top Rotobaler, 1957 IH Golden Jubilee... I'm either a collector, or crazy! |
Replies:
Posted By: GlenninPA
Date Posted: 05 Jun 2012 at 6:39am
|
There is nothing like spending a day with friends, working on a tractor! ------------- Good judgment comes from experience. Experience comes from bad judgment. From listening comes wisdom and from speaking comes repentance. Wise men learn more from fools than fools from the wise. |
Posted By: DonDittmar
Date Posted: 05 Jun 2012 at 6:41am
|
I'll Second what Glenn Says!!!
Right now I am working with my uncle(which I do alot) on an IH 560D needing a crank. You dont realize it, but you are making memories!!!! ------------- Experience is a fancy name for past mistakes. "Great moments are born from great opportunity" 1968 D15D,1962 D19D Also 1965 Cub Loboy and 1958 JD 720 Diesel Pony Start |
Posted By: B26240
Date Posted: 05 Jun 2012 at 6:44am
| And now you have a much greater understanding of the "workins" of your tractor!! |
Posted By: Chuck(ONT)
Date Posted: 05 Jun 2012 at 6:57am
|
I'll third that, spent a day and half with Don Dittmar, his dad and uncle putting brakes on my WD45. Both pins were not coming out by trying everything including drilling and taping, slide hammer, you name it. Thanks again Don.
------------- Never take life too seriously. Nobody gets out alive anyway! 1C 1 WD45 1 AC180 |
Posted By: DonDittmar
Date Posted: 05 Jun 2012 at 8:53am
|
No problem Chuck. They came out with the Gas Axe........ ------------- Experience is a fancy name for past mistakes. "Great moments are born from great opportunity" 1968 D15D,1962 D19D Also 1965 Cub Loboy and 1958 JD 720 Diesel Pony Start |
Posted By: j.w.freck
Date Posted: 05 Jun 2012 at 9:54pm
| don ditmar...never heard the term gas axe,but very fitting...a plasma cutter works wonders too... |
Posted By: CAdon
Date Posted: 06 Jun 2012 at 10:17pm
|
i'm about to face the same issue - double split to get the drive shaft back where it belongs - so i appreciate the picture. now if i could just borrow steve for a day or so... :) and i agree with B26240. nice to be more familiar with how everything works. a neighbor gave me a small but useful old sears suburban which is now almost completely apart, cleaning and painting as i go. learning a lot in the process. hope to do the same soon to a B and make bill long smile... ------------- 52 CA, 41 B and a little B1 oh, yeah... and an 8N ford snuck in there, too. |