WD handclutch lever bushings
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=46862
Printed Date: 27 Jun 2025 at 12:30am
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: WD handclutch lever bushings
Posted By: Mike56073
Subject: WD handclutch lever bushings
Date Posted: 07 Mar 2012 at 8:59pm
| Looking for the dimensions of the handclutch lever bushings, and if anybody has part numbers other than AGCO. |
Replies:
Posted By: SteveM C/IL
Date Posted: 07 Mar 2012 at 9:59pm
| Don't think there were ever bushings.Just pin and bore.They say you can drive pin out from inside and drive new one in,then get your lever bored and sleeved for a "like new" fit. |
Posted By: Lonn
Date Posted: 07 Mar 2012 at 10:27pm
|
It's been many years buy I'm pretty sure I bought bushing(s) from Allis back when it was Deutz-Allis. I know on my WD I installed bushings and I think it had a them in already. ------------- -- --- .... .- -- -- .- -.. / .-- .- ... / .- / -- ..- .-. -.. . .-. .. -. --. / -.-. .... .. .-.. -.. / .-. .- .--. .. ... - Wink I am a Russian Bot |
Posted By: Ted J
Date Posted: 08 Mar 2012 at 5:55am
|
Got mine in La Crosse at 'Lackore Electric Motor Repair', an electrical supply house. There is one in Winona, MN too. I don't remember what I paid for them though. It was a couple of years ago. Here are the addresses: Lackore Electric Motor Repair 108 W 2nd Street Winona, MN 55987 Phone: 507-452-3103 Lackore Electric Motor Repair 4102 Mormon Coulee Court La Crosse, WI 54601 Phone: 608-782-7635 or Phone: 608-783-8012 Check in your area for any Electric Motor Repair places. You might have some good luck. Oh yeah, I think they were 3/4" I.D. x 7/8" O.D. if memory serves... Most of the time it doesn't, if you know what I mean... LOL ------------- "Allis-Express" 19?? WC / 1941 C / 1952 CA / 1956 WD45 / 1957 WD45 / 1958 D-17 |
Posted By: Matt MN
Date Posted: 08 Mar 2012 at 7:58am
|
Yes, agco has them, Part #70224705 requires 2 pieces, very spendy ------------- Unless your are the lead horse the scenery never changes!! |
Posted By: Brian G. NY
Date Posted: 08 Mar 2012 at 8:31am
|
The lever was bushed with two bushings eff. tractor ser. #34450 and up.
I would guess (once you determined the size needed) you could buy bushings much cheaper some place other than Agco.
|
Posted By: Skyhighballoon(MO)
Date Posted: 08 Mar 2012 at 9:01am
|
I re=bushed both the foot clutch pedal and the hand clutch pedal on my WD45. Here's the pivot point measurements I took for each: * Foot clutch: ID: 1.00", 1.75" long * Hand clutch: ID: 7/8", OD: 1", 2.125" long I priced the hand clutch bushing from AGCO. Part number 70224705 was $33.88 EACH and it takes two. I went to McMaster-Car instead. Ordered part number 2868T192, a Bronze SAE 863 bushing 1.5" long. Cut it in half and put one half in from each side. Price: $2.68. The foot clutch did not have a bushing so I drilled it out to 1 1/8. I ordered TWO 2868T201 Bronze SAE 863 bushings 1" long for $1.75 each. Cut one down 1/4 inch to get to 1.75 total length and installed both in the foot clutch. My pivot shaft was worn a bit so it's not perfect and not all the wobble is removed but it is about 300% better than before. HTH. Mike ------------- 1981 Gleaner F2 Corn Plus w 13' flex 1968 Gleaner EIII w 10' & 330 1969 180 gas 1965 D17 S-IV gas 1963 D17 S-III gas 1956 WD45 gas NF PS 1956 All-Crop 66 Big Bin 303 wire baler, 716H, 712H mowers |
Posted By: JoeO(CMO)
Date Posted: 08 Mar 2012 at 9:08am
|
Mike; are you going to the Derry Brownfield auction this weekend? ------------- |
Posted By: Mike56073
Date Posted: 08 Mar 2012 at 11:00am
| No, I'm not. |
Posted By: Skyhighballoon(MO)
Date Posted: 08 Mar 2012 at 12:32pm
LOL - That comment from Joe was for me I'm sure. Mike ------------- 1981 Gleaner F2 Corn Plus w 13' flex 1968 Gleaner EIII w 10' & 330 1969 180 gas 1965 D17 S-IV gas 1963 D17 S-III gas 1956 WD45 gas NF PS 1956 All-Crop 66 Big Bin 303 wire baler, 716H, 712H mowers |
Mike56073 wrote: