Farm Equipment - new holland 268 hayliner question

Print Page | Close Window

new holland 268 hayliner question

Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=33179
Printed Date: 04 Apr 2026 at 3:15am
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com

Topic: new holland 268 hayliner question

Posted By: craigreavley
Subject: new holland 268 hayliner question
Date Posted: 01 Jul 2011 at 8:28pm

baled tonight, and the baler knots are coming apart. The one side ties and both ends of the string are not hanging past the knot. One of the strings is only half out of the knot and the other half is wrapped in the knot what would be causing this

Replies:

Posted By: norm[ind]
Date Posted: 01 Jul 2011 at 8:30pm

CHECK THE BILL HOOKS FOR WEAR OR BENT

Posted By: craigreavley
Date Posted: 01 Jul 2011 at 8:40pm

i am not sure what a worn billhook would look like. There is some play up and down on the bill hook shaft the good knotter is tight the bad knot side has an eighth inch play up and down on the billhook shaft could that play be the issue

Posted By: Teddy (punchie)
Date Posted: 01 Jul 2011 at 9:22pm

The side with the looped knot: I don't have a book here but that is a common problem, I can tell you it is almost never a billhook (worn will have a grove, in the hook or the tuque ) make sure it is smooth if not steel wool it until all rust is gone and roughness is gone. I'm thinking it is tension at the twine box, or twine holder, I know the 273 NH twine holder at the knotter can break very easy if over tightened. Just a piece of spring steel, sometimes they wear out. You should not be able to pull the twine out of the knotter easily, should take about 60-80 lbs to pull it out, only make it tight enough to hold the twine to make a knot. There is also a tensioner on the billhook that need to be checked.

The uneven knot ends maybe a the knife needs sharpened.

-------------
Ac D-19, a Number of WD's, One WD45, Two 444 balers, Ac plows and etc.

Posted By: BobHnwO
Date Posted: 02 Jul 2011 at 4:26am

What Teddy said,make sure knives are sharp.

-------------
Why do today what you can put off til tomorrow.

Posted By: mtanut
Date Posted: 02 Jul 2011 at 5:30am

Other thing to check is the knife arm. Take the bolt out of the bottom of the knotter, then swing it up in the air, pull the cotter key and remove the knife arm. There is a brass ball on to of the arm and over the years it will develop flat spots on it.When the knotter cycles it won't work smooth and hang up in the casting, hence the not cutting right and hanging up on one side. Good luck balers are a love hate relationship.

-------------
I have a 185 Allis, 6060 Allis, Model K gleaner, SMTA ferg 35, ferg 20 (paps first tractor, Allis B (wife's)John Deere 240 skid loader and a bunch of the usual farm stuff.

Posted By: kev/ont
Date Posted: 02 Jul 2011 at 7:06am

I would check for a bent twine finger. It sounds like the #2 twine is not being delivered to the knotter properly. Also make sure the twine discs are timed properly, if there not uneven cutting of the string will result. As well bill hook tongue pressure may be too light resulting in the ends of the twine pulling out of the billhook before the knifearm can wipe the knot off. Good luck

Posted By: CORLEWFARM
Date Posted: 03 Jul 2011 at 11:23am

CHECK THE GEAR ON THE BIRDBILL THE FLAT SPOT SHOULD BE COMPLETELY FLAT.IT LETS THE BIRDBILL MOVE TOO MUCH IF WORN