rc rims
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=29833
Printed Date: 31 Dec 2025 at 5:40pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: rc rims
Posted By: beaker41
Subject: rc rims
Date Posted: 26 Apr 2011 at 9:18pm
| im just wondering does anybody know if there are rims from a different tractor that will fit on a 39 rc i have been looking for some used ones but their does not seem to be any around anywhere |
Replies:
Posted By: Matt MN
Date Posted: 26 Apr 2011 at 9:23pm
|
Front or rear? I beleive there some Massey Harris tractors that used the same front rim. ------------- Unless your are the lead horse the scenery never changes!! |
Posted By: TomMN
Date Posted: 26 Apr 2011 at 9:26pm
If your centers are still good you can do what I did: take the old rivets out and get new rim blanks from Steiner:  I think the right rim blank is part number IHS195: http://www.steinertractor.com/IHS195-front-wheel - http://www.steinertractor.com/IHS195-front-wheel |
Posted By: beaker41
Date Posted: 26 Apr 2011 at 9:35pm
|
its for the rear rims |
Posted By: WC7610
Date Posted: 26 Apr 2011 at 10:14pm
|
Hi Beaker41,
We had one beyond repair for Dad's RC and bought a new one from Norm Meinert at Norm's Toys.
 ------------- Thanks Most Bad Government has grown out of Too Much Government- Thomas Jefferson |
Posted By: SHAMELESS
Date Posted: 26 Apr 2011 at 10:31pm
| think eisenmaan's in madison,ne has them...i inquired about the front and rear rims there last fall for my RC, he had them then, but i didn't have the money at that time! |
Posted By: R Aiken
Date Posted: 26 Apr 2011 at 10:51pm
| On my 39 RC, I used a rear rim off a Case VAC. They are the ones with the continous rib instead of the 6 humps. I had to change the location of the block that keeps it from slipping. |
Posted By: B26240
Date Posted: 27 Apr 2011 at 7:13am
| R Aiken again is right they should have a continous rib all the way around instead of dimples. I think they are only 9" wide also. |
Posted By: Bob-Maine
Date Posted: 27 Apr 2011 at 7:34am
|
Norm Meinert and Norm's Toys are not the same. My recollection is that Norm Steinman owns Norm's Toys and Norm Meinert operates a business under his own name. Both advertise in the Old Allis News. Bob@allisdowneast ------------- I used to think I was indecisive, but now I'm not sure. |
Posted By: WC7610
Date Posted: 27 Apr 2011 at 7:36am
|
Bob, you are correct. My apologies to both.
We got the rim from Norm's Toys. It is a 9" rim correct in size for the RC, but as Ray pointed out, it has the dimples instead of the continuous ridge. ------------- Thanks Most Bad Government has grown out of Too Much Government- Thomas Jefferson |
Posted By: Fields
Date Posted: 27 Apr 2011 at 7:46am
| If i remember right the rears had only one scalp not two like the wc rims. that is on the cast center. Would press steel that was availble for the wc at the time be correct? |
Posted By: Bill Deppe/AC Salvag
Date Posted: 27 Apr 2011 at 9:03am
| New rims, 9 or 10 inches wide are about $150 ea plus ship. |
Posted By: Tony.Or
Date Posted: 27 Apr 2011 at 9:12am
|
I can provide single bevel rims or bump rims. 1-877-602-3994 Tony ------------- http://www.tonystractors.com" rel="nofollow - http://www.tonystractors.com |
Posted By: GreenOrange
Date Posted: 27 Apr 2011 at 6:20pm
| 10 " is the correct width for RC's. 10x28 or 11.2x28 (new size). |