Farm Equipment

Print Page | Close Window

parts

Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=192669
Printed Date: 24 Oct 2025 at 6:33pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com

Topic: parts

Posted By: combinechris
Subject: parts
Date Posted: 31 Dec 2022 at 11:47am

looking for a place to get cylinder bars for an E gleaner combine as mine are pretty worn. i'm also looking for the shaft lengths for the drive shaft on the cornhead for the 60/66 combine since i will have to make one for mine . thanks in advance.

-------------
35 combines and 15 forage harvesters. mostly allis combines and equipment.WTB 2 row cornhead for a 90

Replies:

Posted By: DrAllis
Date Posted: 31 Dec 2022 at 5:23pm

Cylinder bars for E-E3-K-K2 are all the same.

Posted By: combinechris
Date Posted: 31 Dec 2022 at 5:38pm

DrAllis where do you get them from?

-------------
35 combines and 15 forage harvesters. mostly allis combines and equipment.WTB 2 row cornhead for a 90

Posted By: SteveM C/IL
Date Posted: 31 Dec 2022 at 8:23pm

AGCO has them at $330 apiece. If yours aren't worn paper thin but the top is worn down,you can send them to Trimpe in Seymour IN for welding up. May have a set ready for sale.

Posted By: DrAllis
Date Posted: 31 Dec 2022 at 8:46pm

I just looked in a Shoup catalog and they don't have them. I'd guess the $330 price is a pair, but still $1320 for a full set of 8 bars. Trimpe bars are great for corn and soybeans. Won't work well for small grains.

Posted By: Mikez
Date Posted: 31 Dec 2022 at 8:51pm

What are the part numbers

Posted By: SteveM C/IL
Date Posted: 01 Jan 2023 at 1:02am

AGCO just gives Pt #,price and says 8 required. To me that means X apiece. A dealer can find out.

Trimpe usually cuts out every other rib to make wide spaced bars. No reason they couldn't build up all ribs on std bar for small grains.

Posted By: ryan(IN)
Date Posted: 01 Jan 2023 at 9:50am

That price is per pair

-------------
ryan
1984 8070 FWA,1979 7060,1975 7040,1971 190,1960 D-17D,1957 D-14, 196? D-19G, 1975 5040,1971? 160,1994 R62

Posted By: SteveM C/IL
Date Posted: 01 Jan 2023 at 1:48pm

Thanks for the clarification Ryan

Posted By: DrAllis
Date Posted: 01 Jan 2023 at 3:21pm

They were sold in pairs for balance. Remove one old cyl bar and replace with new. Turn the cylinder 180 degrees and remove/replace the next one to keep cylinder balanced.

Posted By: SteveM C/IL
Date Posted: 01 Jan 2023 at 9:03pm

I always marked mine on the backside with letter stamps to keep the pairs together. Used to run just 4 in the A2 in beans. Was a HOGG and would eat all the green weeds you could feed it...had to keep an eye on the chopper belt after a big bite of that.

Posted By: combinechris
Date Posted: 01 Jan 2023 at 9:07pm

Thanks for all the information guys. Now I have someplace to start.

-------------
35 combines and 15 forage harvesters. mostly allis combines and equipment.WTB 2 row cornhead for a 90

Posted By: only AC orange
Date Posted: 03 Jan 2023 at 2:25pm

How bad are they worn? On both my "E" and "K" (years ago), I took them off and turned them 1/2 turn and had a new wear surface!

Posted By: Clay
Date Posted: 03 Jan 2023 at 3:15pm

St. Johns Welding & Mfg Inc.

St. Johns Kansas

Fax 620-549-3262

TollFree 800-549-3289Welding & Mfg Inc.

These people have been in business a very long time. They do an excellent job.

Posted By: combinechris
Date Posted: 03 Jan 2023 at 4:10pm

I can shave with them

-------------
35 combines and 15 forage harvesters. mostly allis combines and equipment.WTB 2 row cornhead for a 90

Posted By: combinechris
Date Posted: 03 Jan 2023 at 4:12pm

The price is each Ryan. The cost for a set of 8 bars is a little over 2700.

-------------
35 combines and 15 forage harvesters. mostly allis combines and equipment.WTB 2 row cornhead for a 90