200 hight reduction.
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=185070
Printed Date: 20 Aug 2025 at 12:20am
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: 200 hight reduction.
Posted By: Mikez
Subject: 200 hight reduction.
Date Posted: 11 Dec 2021 at 4:21pm
|
hello Could we loose five or six inches if we let some air out of tires. Want to get it into garage to do some work on it. Figured I’d ask and see if anyone has done it before messing with valve stems lol. Thanks
|
Replies:
Posted By: Dirt Farmer
Date Posted: 11 Dec 2021 at 5:14pm
| If it doesnt have a cab just take the muffler off to clear, in my experience if the tires don't have calcium in them the air can be left out to get in garage then air them back up once in the garage to keep from pinching the innertube drive as short a distance as possible with low air pressure. |
Posted By: DiyDave
Date Posted: 11 Dec 2021 at 6:47pm
You could get a mohel to take 6" off the pipe. Won't help if it has a cab, though! ------------- Source: Babylon Bee. Sponsored by BRAWNDO, its got what you need! |
Posted By: Mikez
Date Posted: 11 Dec 2021 at 8:26pm
| yes sorry. Cab is what we’re trying to clear, and rear tires are loaded. I figured we’d put valve stem at top measure tire let air out tell see fluid see what we got. |
Posted By: DanWi
Date Posted: 11 Dec 2021 at 9:47pm
| If they are full of fluid, you will have fluid coming out before you drop 6 inches. Unless they aren't full. You could get an adapter, valve stem to a garden hose and let some fluid out. |
Posted By: HudCo
Date Posted: 12 Dec 2021 at 10:13am
| you can let them down real low even with fliud you do it with the stems on top had to do that in the old shop with 10 foot doors |
Posted By: PaulB
Date Posted: 12 Dec 2021 at 12:01pm
|
See what a PIA fluid filled tired are ! ------------- If it was fun to pull in LOW gear, I could have a John Deere. Real pullers don't have speed limits. If you can't make it GO... make it SHINY |
Posted By: CORLEWFARM
Date Posted: 12 Dec 2021 at 2:35pm
| See what a PIA small shop doors are. |
Posted By: BKarpel
Date Posted: 12 Dec 2021 at 8:07pm
| Could make a stand on wheels to support rear end or drawbar support. Then remove the tires and push into shop. Alot of work but doable. |
Posted By: SteveM C/IL
Date Posted: 13 Dec 2021 at 9:37am
| Guess it depends on how bad you need to work on it. Be a good time for a friend with bigger building. |
Posted By: Acdiesel
Date Posted: 13 Dec 2021 at 10:47am
|
If your barn only has a Dirt or Gravel floor you could dig it out to get under/past your door. ------------- D19 Diesel,D17 Diesel SER.3 2-D14, 2-D15 SER.II WF/NF D15 SER.2 DIESEL D12 SER.I, D10 Ser.II 2-720'S D21 Ser. II Gmc,caterpillar I'm a pharmacist (farm assist) with a PHD (post hole digger) |
Posted By: injpumpEd
Date Posted: 13 Dec 2021 at 10:51am
|
I'd think you could sneak by with a couple of inches, but 6 is probably a bit much.
------------- 210 "too hot to farm" puller, part of the "insane pumpkin posse". Owner of Guenther Heritage Diesel, specializing in fuel injection systems on heritage era tractors. stock rebuilds to all out pullers! |
Posted By: SteveM C/IL
Date Posted: 13 Dec 2021 at 11:44am
| I guess you won't know til you try |
Posted By: Mikez
Date Posted: 13 Dec 2021 at 4:06pm
| lol thanks guys. We let some out tell we felt comfortable and we were like inch or two still to high. So we’re working outside. Funny my grandfather was a dealer here. Before they thought of cabs ha. |
Posted By: PaulB
Date Posted: 13 Dec 2021 at 6:20pm
|
Yep: Most building doors were just fine when they were built 50+ years ago. ------------- If it was fun to pull in LOW gear, I could have a John Deere. Real pullers don't have speed limits. If you can't make it GO... make it SHINY |