6060 PTO housing vs. A 6080
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=170580
Printed Date: 28 Jul 2025 at 6:37am
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: 6060 PTO housing vs. A 6080
Posted By: allis6080
Subject: 6060 PTO housing vs. A 6080
Date Posted: 26 Apr 2020 at 6:51pm
|
So I was pulling my truck and trailer out of the wet yard with my 6060 put chain around the draw bar carrier and well need less to say it pulled the bolts out of the PTO housing instead of pulling my truck and trailer. So my question is will a 6080 PTO housing swap easily to the 6060? I have a 6080 parts tractor out back. Thanks for any help or info. ------------- 6060 s\n 5016 1947 JD B |
Replies:
Posted By: DSeries4
Date Posted: 26 Apr 2020 at 9:26pm
|
Another hard lesson learned that a drawbar carrier is NOT a pull point. It holds the drawbar up, that's it. That's why I keep a clevis in the tool box. I do not think the 6080 rear end is the same. These 2 tractors used transmissions and rear ends from 2 separate Fiat models. One was 8 speed and one was 12 speed as well. ------------- '49 G, '54 WD45, '55 CA, '56 WD45D, '57 WD45, '58 D14, '59 D14, '60 D14, '61 D15D, '66 D15II, '66 D21II, '67 D17IV, '67 D17IVD, '67 190XTD, '73 620, '76 185, '77 175, '84 8030, '85 6080 |
Posted By: allis6080
Date Posted: 27 Apr 2020 at 5:20am
|
Yeah definitely a hard lesson. I'm going to make some calls today and see if I can get a used housing. My luck it will cost a fortune. ------------- 6060 s\n 5016 1947 JD B |
Posted By: allisrutledge
Date Posted: 27 Apr 2020 at 7:20am
| I put one on mine last winter, was broke when I got it and I got tired of constantly worrying about it. I ordered it from someone in OH I think. I do remember it has 6070 on it with a paint marker. I don't know if that's correct but it fit. I also machined some rings and pressed them over the round nubs where the hitch bolts to reinforce it some. Mine was broke out at the bottom like it was overloaded? I'll see if I got a picture |
Posted By: allisrutledge
Date Posted: 27 Apr 2020 at 7:55am
  ------------- Allis Chalmers still exist in my mind and barns |
Posted By: TramwayGuy
Date Posted: 27 Apr 2020 at 9:15am
| Parts books show the rear housings are indeed different. Can you heli-coil the holes? |
Posted By: allis6080
Date Posted: 27 Apr 2020 at 9:20am
|
I still need to look at it a little more yet I have a machinist friend that may be able to re machine the holes ------------- 6060 s\n 5016 1947 JD B |
Posted By: allisrutledge
Date Posted: 27 Apr 2020 at 9:25am
|
By the way that is metric bolts, I think m20x2.5 pitch. I can look on my receipt from McMaster Carr if needed. ------------- Allis Chalmers still exist in my mind and barns |
Posted By: allis6080
Date Posted: 27 Apr 2020 at 9:36am
|
Brenda from Sandy lake implement said m18x1.50x 130 bolts ------------- 6060 s\n 5016 1947 JD B |
Posted By: allis6080
Date Posted: 27 Apr 2020 at 9:37am
|
Thanks ------------- 6060 s\n 5016 1947 JD B |
Posted By: allisrutledge
Date Posted: 27 Apr 2020 at 9:38am
|
18 is correct ------------- Allis Chalmers still exist in my mind and barns |
Posted By: wekracer
Date Posted: 28 Apr 2020 at 8:27am
| Someone told me a while back that they could be tapped to 3/4 if I remember correctly. Don’t remember if it was fine or coarse thread. |
Posted By: allisrutledge
Date Posted: 28 Apr 2020 at 9:36am
|
Taping to 3/4-16 would work if drilled to 11/16 .687 and its stripped and not broke out. M18 drill to tap is a little smaller ------------- Allis Chalmers still exist in my mind and barns |
Posted By: allis6080
Date Posted: 30 Apr 2020 at 6:48pm
You guys are right my buddy is going to drill and tap them for me. Thanks for all the replies. ------------- 6060 s\n 5016 1947 JD B |
allisrutledge wrote:Posted By: allisrutledge
Date Posted: 01 May 2020 at 7:01am
| Great they were not busted, mine was broke out beyond reasonable repair due to some kind of rough treatment by previous owner. I nursed it as long as I could and then replaced it. Scott |