Hydraulic Cylinder for WD45 and wheel disk
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=156352
Printed Date: 18 Jul 2025 at 1:35pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: Hydraulic Cylinder for WD45 and wheel disk
Posted By: woodman Steve
Subject: Hydraulic Cylinder for WD45 and wheel disk
Date Posted: 12 Dec 2018 at 10:11am
|
Where can one find a one way cylinder that will work with my WD45 system for my wheel disk? ------------- Steve Two WD45's |
Replies:
Posted By: john(MI)
Date Posted: 12 Dec 2018 at 1:49pm
|
Any cyl with adequate length and the correct ends will work. You would just put a vent cap on the unused end of the cyl. if it's a two way cyl. ------------- D14, D17, 5020, 612H, CASE 446 |
Posted By: MACK
Date Posted: 12 Dec 2018 at 9:46pm
|
Needs to be a hi pressure cylinder and hose. I have one that I don't use any more that I would sell. MACK |
Posted By: SteveM C/IL
Date Posted: 12 Dec 2018 at 9:59pm
| The original AC cylinders work best.They are still out there. High pressure,low volume. |
Posted By: dawntreader74
Date Posted: 12 Dec 2018 at 11:23pm
| have one i may sell also; |
Posted By: PaulB
Date Posted: 13 Dec 2018 at 3:00am
|
I have a few of them available. Some are NOS. ------------- If it was fun to pull in LOW gear, I could have a John Deere. Real pullers don't have speed limits. If you can't make it GO... make it SHINY |
Posted By: Gary Burnett
Date Posted: 13 Dec 2018 at 6:28am
I have heard that for years but never have had a problem using regular cylinders on AC tractors.Have you ever actually had a problem?
|
MACK wrote:Posted By: MACK
Date Posted: 13 Dec 2018 at 7:39am
| They will stretch the bolts on a low pressure cylinder then blow orings + will lift slow. MACK |
Posted By: Gary Burnett
Date Posted: 13 Dec 2018 at 8:33am
Guess I've been lucky never had a problem, have a regular cylinder on a NH mower now I've used quite a bit hooked to a D15 and a WD.What brand cylinder were you using when it happened?
|
Posted By: alchpuller
Date Posted: 13 Dec 2018 at 10:40am
|
I have some aircraft MLG cylinders, 3000 psi system mineral oil fluid , 303 fluid works good 18 in travel extend only, you pay shipping and 10$ a piece, I use them on a bale mover and they work good with my WD45
|
Posted By: CTuckerNWIL
Date Posted: 13 Dec 2018 at 4:56pm
|
I have a 2 way Oliver cylinder I used on the 45 for several years, to lift the corn planter. Never had a problem, but I never let it hammer after it was extended all the way. If you raise it up out of the ground and move the lever to the hold position, you'll never have a problem with any 2 way remote cylinder. It will be slower than a regular Allis cylinder. I eventually found a cheap Allis cylinder at an auction. Gave $8 for it and then spent about $30 and 3 hours of my time to make a new rod and put new packing in it. ------------- http://www.ae-ta.com" rel="nofollow - http://www.ae-ta.com Lena 1935 WC12xxx, Willie 1951 CA6xx Dad bought new, 1954WD45 PS, 1960 D17 NF |
Posted By: truckerfarmer
Date Posted: 13 Dec 2018 at 11:09pm
|
Most modern cylinders are made to handle at least 3000psi. Unless you have rebuilt the pump, it's probably not getting that high of pressure anymore. ------------- Looking at the past to see the future. '53 WD, '53 WD45, WD snap coupler field cultivator, #53 plow,'53 HD5B dozer Duct tape.... Can't fix stupidity. But will muffle the sound of it! |
Posted By: Lonn
Date Posted: 14 Dec 2018 at 6:48am
|
Dad's WD pushed a wagon hoist cylinder apart once. After that Dad gave strict orders to not let the wagons go but so high. ------------- -- --- .... .- -- -- .- -.. / .-- .- ... / .- / -- ..- .-. -.. . .-. .. -. --. / -.-. .... .. .-.. -.. / .-. .- .--. .. ... - Wink I am a Russian Bot |