Hydraulic questions 8010
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=150393
Printed Date: 27 Jul 2025 at 11:46am
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: Hydraulic questions 8010
Posted By: Chad80
Subject: Hydraulic questions 8010
Date Posted: 12 May 2018 at 1:11pm
| I have a question about hydraulics, My tractor is an 8010 and I was using it the other day Mowing with a 15' battling mower. It would let me raise the bath wings but it would not let me control my height level. I disconnected in hotep to other implements having the same issues sometimes I cannot get my remote to work at all. I have 3 remotes on this tractor and all of them are doing the same thing. Any suggestions? |
Replies:
Posted By: Ron(AB)
Date Posted: 12 May 2018 at 1:25pm
|
If it was just one lever...I'd say adjust the cable. If it is all three levers...check hyd filter, oil level, hoses, then pump pressure. standby pressure, etc. |
Posted By: MACK
Date Posted: 12 May 2018 at 10:18pm
| Could be bad couplers. If it has levers on couplers, that would be a good place to start. MACK |
Posted By: wekracer
Date Posted: 13 May 2018 at 7:14am
| I have had problems with a fertilizer buggy doing that one time. One coupler had pressure and wouldn’t release the tip even though it was plugged in. It is a pain. Good luck. |
Posted By: Chad80
Date Posted: 14 May 2018 at 7:45pm
| Mack, where can i buy replacement coullers? I have do have the style coupler you mentioned. |
Posted By: tornado8070
Date Posted: 14 May 2018 at 9:30pm
If it has the lever lock style couplers throw them in the  can, call salvage yard and get the earlier style couplers get the adapter nipple to plumb and never have to worry about them again.------------- 09’ DT205B, 08’ DT220A, 83' 8070 MFWD, 83’ 8070 85’ 8050 MFWD, 83' 8030, 82' 8010, 85’ 6080 MFWD, 84’ 6080, 79' 7020, 85' M3 RWD, 85' 920 diesel,AC C-50 forklift. |
Posted By: MACK
Date Posted: 14 May 2018 at 9:49pm
| Your Agco dealer should have then or most farm supply store. MACK |
Posted By: Transaxial
Date Posted: 15 May 2018 at 8:38am
Since you call this problem "sometimes" it might be a coupler problem but that usually does not happen to all of them at one time. Just something to think about is a little spring in the hydraulic pump (3/8" dia x 1/2" long and some shims) that sets the standby pressure of the pressure comp circuit. It is accessible through a plug on the outside of the pump and I have had it break which just stops all hydraulic function. If yours is broken such that you have reduced pressure , you could have intermittent hydraulic function??? Just a far out guess!! |
Chad80 wrote:Posted By: Mikez
Date Posted: 18 May 2018 at 11:54pm
| Tornado do you have a picture of your couplers after you changed it |
Posted By: Ron(AB)
Date Posted: 19 May 2018 at 1:56pm
|
Posted By: Mikez
Date Posted: 20 May 2018 at 11:12pm
| I ask because I'm looking at a 8050 and it has lever type and it has wire tie around them, and couplers look different then others IV seen with lever type |