WD45 SMV sign
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=141143
Printed Date: 28 Apr 2025 at 5:12pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: WD45 SMV sign
Posted By: Clay
Subject: WD45 SMV sign
Date Posted: 05 Aug 2017 at 10:50pm
|
Looking for photos of SMV sign on the rear of a WD45. How and where did you attach the SMV to the rear of the WD45?
|
Replies:
Posted By: dawntreader74
Date Posted: 05 Aug 2017 at 11:57pm
| use that notch in the flat plate on the back of the tractor. would be right in the middle of the rear end. works good' better than putting a hole in the finder or some place you wish you would not of did later down the road' got one there for going on rides' works well.. |
Posted By: Orange Blood
Date Posted: 06 Aug 2017 at 7:42am
|
I have seen a chunk of 3/4" All-thread up about 36" from the hitch and offset out rearward about a foot. I thought this was pretty neat, as you could move it from tractor to tractor, if all you really do are tractor drives. It was double nutted on the top of the hitch, with a big square washer another one on the bottom, and a single nut with wings welded to in on the bottom, made out of 1/4" rod about 3" long each. Sign at the top was attached to a piece of flat stock welded to the top of the all-thread. ------------- Still in use: HD7 WC C CA WD 2-WD45 WD45LP WD45D D14 3-D17 D17LP 2-D19D D19LP 190XTD 190XTLP 720 D21 220 7020 7030 7040 7045 3-7060 Projects: 3-U UC 2-G 2-B 2-C CA 7-WC RC WDLP WF D14 D21 210 7045 N7 |
Posted By: bradley6874
Date Posted: 06 Aug 2017 at 12:28pm
|
Had ours mounted on flat bar on the outside of the fender bracket was bolted to the fender mount and contoured the fender stuck out over the tire with smv and blinking lights no holes in fender dad made a pinch clip to grip flange of the fender hope that helps ------------- You can wash the dirt off the body but you can’t wash the farmer out of the heart and soul |
Posted By: Dakota Dave
Date Posted: 06 Aug 2017 at 6:47pm
| I just hang it off the seat with a piece of electric fence wire. My other WD45 has it screwed to the cab door. |
Posted By: plummerscarin
Date Posted: 06 Aug 2017 at 6:53pm
| Dad fabbed his from flat plate and also used existing holes on fender bracket to mount over the left side tire. |
Posted By: Bill_MN
Date Posted: 06 Aug 2017 at 10:58pm
|
Bolted mine through hole in middle back of pan seat with carriage bolt. Smooth head on top surface of seat doesn't catch on you. ------------- 1951 WD #78283, 1918 Case 28x50 Thresher #76738, Case Centennial B 2x16 Plow |
Posted By: Sugarmaker
Date Posted: 08 Aug 2017 at 7:19am
I mounted mine on a twisted metal strap hanging from the back bolt inside the left fender. This puts the sign pretty low, which is OK for just the tractor but not good if you have a wagon. Which should have its own anyway. I like this spot because its out of the way. Regards, Chris ------------- D17 1958 (NFE), WD45 1954 (NFE), WD 1952 (NFE), WD 1950 (WFE), Allis F-40 forklift, Allis CA, Allis D14, Ford Jubilee, Many IH Cub Cadets, 32 Ford Dump, 65 Comet. |