my 37 wc puller, 400 cube motor
Printed From: Unofficial Allis
Category: Other Topics
Forum Name: Pulling Forum
Forum Description: Forum dedicated to Tractor and Garden Pulling
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=125605
Printed Date: 31 Oct 2025 at 5:56am
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: my 37 wc puller, 400 cube motor
Posted By: Robacpuller
Subject: my 37 wc puller, 400 cube motor
Date Posted: 08 Jul 2016 at 6:18pm
  
|
Replies:
Posted By: Robacpuller
Date Posted: 08 Jul 2016 at 6:25pm
  Rest of picks |
Posted By: mjbower
Date Posted: 08 Jul 2016 at 10:05pm
|
WOW 400 cubic inches amazing luv the unstyled wc good luck with It |
Posted By: Zaddison
Date Posted: 08 Jul 2016 at 11:47pm
| What kind of classes/divisions do you pull with that? |
Posted By: Robacpuller
Date Posted: 09 Jul 2016 at 7:21am
| 3500 to 6000, I'm pulling tommorow in a 60000 farm class. 8 mph, but I don't go that fast, I will do about 5mph at 2500 rpms. Will b pulling against some big iron. Last year I got 8th out of 15 tractors. Not bad for a little wc. I would have done better but stood front up and I had 500 up front, this year I will put more up front. I don't pull that class very often but it is close to home. I usually pull 4000 to 5000 class. They laugh when I show up to pull against m's and 88 olives ect. But I kicked a few of them. It's fun |
Posted By: mjbower
Date Posted: 09 Jul 2016 at 7:37am
| Good to hear the beating up Ms and 88s most importantly is the having fun part good luck |
Posted By: Robacpuller
Date Posted: 09 Jul 2016 at 7:40am
| I am going to video the pull hopefully I can get it on this Web site or u tube. |
Posted By: mike a
Date Posted: 10 Jul 2016 at 8:56am
| nice puller! i moved my seat to the middle about 5yrs ago,pulls straight now.go beat up on those jd's as well! |
Posted By: Charlie175
Date Posted: 11 Jul 2016 at 8:00am
|
What's done to arrive at 400 cubes? ------------- Charlie '48 B, '51 CA, '56 WD45 '61 D17, '63 D12, '65 D10 , '68 One-Ninety XTD |
Posted By: Robacpuller
Date Posted: 11 Jul 2016 at 8:10pm
| I bored the block to 4.600 bore stroked the crank to 6 inches. Big block chev pistons, 8 inch 350 international rods. The head is stock wc but a lot of porting and polishing. Big block chev valves 192 intakes 160 exhaust. Intake is ported and polished to Mach head. The carb is from a D17, but I opened it up real big I made a new ventury 1.480. I run 20% over rpms. Cam is ground. I pulled on Sunday in 6000 lb. Class and I ran out of power, it was an 8 mph class Iran 5 mph, a lot of the tractors were 100 hp more than me. I got 8th out of 16.Not bad for a 110 hp wc. A lot of old timers gave me the thumbs up. I recorded it so if I get it figured out I will have it on this site. I did all the work myself, my friend bored the block. The crank is a Merfeld crank. I didn't have grind much off the block to get clerance using the 350 rods. It is D17 block and crank. I would like to start building these motors for people it was fun doing. |
Posted By: Robacpuller
Date Posted: 20 Aug 2016 at 5:45pm
| I got a video of my wc pulling at sauk ffa pull. To see it go to you tube and put in sauk pull 37 wc |
Posted By: CTuckerNWIL
Date Posted: 20 Aug 2016 at 7:56pm
|
Or, look at it right here. [TUBE]-tza5TMXDN0[/TUBE] ------------- http://www.ae-ta.com" rel="nofollow - http://www.ae-ta.com Lena 1935 WC12xxx, Willie 1951 CA6xx Dad bought new, 1954WD45 PS, 1960 D17 NF |
Posted By: Robacpuller
Date Posted: 21 Aug 2016 at 3:36pm
| Thanks |
Posted By: joetom08
Date Posted: 21 Aug 2016 at 9:28pm
I sent you a pm |
Robacpuller wrote: