This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


D 12 Manifold
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Tyee II View Drop Down
Bronze Level
Bronze Level


Joined: 06 Dec 2009
Location: Scappoose OR
Points: 66 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Tyee II Quote  Post ReplyReply Direct Link To This Post Topic: D 12 Manifold
    Posted: 29 Mar 2020 at 1:26pm
Been a long time since I was here. I am needing to replace the manifold on my D 12
series 3. looking at the options they look pretty much all the same. Look to be aftermarket offshore cast. Anyone have any experience with these good or bad ? thanks for advance in your replies. While we are sitting tight thought I would do a few projects that have been on the back burner. 
Back to Top
Sponsored Links


Back to Top
PaulB View Drop Down
Orange Level
Orange Level


Joined: 12 Sep 2009
Location: Rocky Ridge Md
Points: 4401 		Post Options Post Options   Thanks (0) Thanks(0)   Quote PaulB Quote  Post ReplyReply Direct Link To This Post Posted: 29 Mar 2020 at 3:31pm
It's been a few years ago that I got a couple from Sandy Lake that were very good quality. I think at the time Brenda had told me that they were getting them done for them rather than buying from a supplier. They were an exact fit and the muffler lined up properly with the hole in the hood. 

Edited by PaulB - 29 Mar 2020 at 8:20pm
If it was fun to pull in LOW gear, I could have a John Deere.
If you can't make it GO... make it SHINY
Back to Top
WF owner View Drop Down
Orange Level
Orange Level


Joined: 12 May 2013
Location: Bombay NY
Points: 4380 		Post Options Post Options   Thanks (0) Thanks(0)   Quote WF owner Quote  Post ReplyReply Direct Link To This Post Posted: 29 Mar 2020 at 3:57pm
Just a suggestion, but you might find a good used manifold on here.
Back to Top
Bill Deppe/AC Salvag View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Location: Maquoketa, Iowa
Points: 968 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Bill Deppe/AC Salvag Quote  Post ReplyReply Direct Link To This Post Posted: 29 Mar 2020 at 4:27pm
Have a couple new ones, $225 + s&h Ia 563 357 2616
Back to Top
DiyDave View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 11 Sep 2009
Location: Gambrills, MD
Points: 50487 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DiyDave Quote  Post ReplyReply Direct Link To This Post Posted: 29 Mar 2020 at 6:14pm
from my experience, about 10-15 years ago, the universal D-10/12/14 offshore cast manifolds move the exhaust pipe about 3/4-1" closer to the left side. some sheet metal timmin may be in the works, if you can't adjust the hood panels to the left, on your tractor...Wink

Edited by DiyDave - 29 Mar 2020 at 6:18pm
Source: Babylon Bee. Sponsored by BRAWNDO, its got what you need!
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.063 seconds.


Help Support the
Unofficial Allis Forum