This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Garden Tractors
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


720 Gas Cap

 Post Reply Post Reply
Author
Message
Dave (NE) View Drop Down
Orange Level
Orange Level


Joined: 12 Sep 2009
Location: Eagle Nebraska
Points: 2148
Post Options Post Options   Thanks (0) Thanks(0)   Quote Dave (NE) Quote  Post ReplyReply Direct Link To This Post Topic: 720 Gas Cap
    Posted: 13 Sep 2024 at 8:17am
For some reason, over the past several months the gas cap on my 720 will not easily come off as it used to.  I have to use considerable pressure to lift and remove it.  Yes, the nob parts on the cap are lined up with the notches in the neck of the tank, so that is not the issue.  Any ideas?   Thanks, Dave
Do not argue with an idiot. He will drag you down to his level and beat you with experience. Mark Twain.
Back to Top
Sponsored Links


Back to Top
AC720Man View Drop Down
Orange Level
Orange Level
Avatar

Joined: 10 Oct 2016
Location: Shenandoah, Va
Points: 4934
Post Options Post Options   Thanks (0) Thanks(0)   Quote AC720Man Quote  Post ReplyReply Direct Link To This Post Posted: 19 Sep 2024 at 9:11pm
It may be the gasket sticking? My 720 would be running fine and then shut off. 20 minutes later it would start and run for 5 minutes and shut off. I lifted the hood and noticed the tank sides were sucked in. Removed the cap and the tank took a big breath of fresh air and the tank sides returned to their normal shape. Replaced both of my 720 caps with one with a gauge . Problem solved.
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
Back to Top
Dave (NE) View Drop Down
Orange Level
Orange Level


Joined: 12 Sep 2009
Location: Eagle Nebraska
Points: 2148
Post Options Post Options   Thanks (0) Thanks(0)   Quote Dave (NE) Quote  Post ReplyReply Direct Link To This Post Posted: 19 Sep 2024 at 9:30pm
Yeah, its like the cap shrunk up or something.  Hot or cold, it doesn't want to easily come off.  Crazy thing!
Do not argue with an idiot. He will drag you down to his level and beat you with experience. Mark Twain.
Back to Top
Herb(GA) View Drop Down
Orange Level Access
Orange Level Access


Joined: 15 Sep 2009
Location: United States
Points: 1037
Post Options Post Options   Thanks (0) Thanks(0)   Quote Herb(GA) Quote  Post ReplyReply Direct Link To This Post Posted: 20 Sep 2024 at 8:07am
I have filed the outside of the tank opening to reduce this tight fit.  First, to be on the safe side I plugged the tank opening with clean rag.  Herb(GA)
Back to Top
Dave (NE) View Drop Down
Orange Level
Orange Level


Joined: 12 Sep 2009
Location: Eagle Nebraska
Points: 2148
Post Options Post Options   Thanks (0) Thanks(0)   Quote Dave (NE) Quote  Post ReplyReply Direct Link To This Post Posted: 20 Sep 2024 at 8:11am
Yeah, I was thinking about doing that on the outside of the tank.  Or, perhaps a wire wheel in my drill and do the inside of the cap.
Do not argue with an idiot. He will drag you down to his level and beat you with experience. Mark Twain.
Back to Top
Gary (sw Wis.) View Drop Down
Silver Level Access
Silver Level Access


Joined: 12 Sep 2009
Location: S.W. Wis.
Points: 207
Post Options Post Options   Thanks (0) Thanks(0)   Quote Gary (sw Wis.) Quote  Post ReplyReply Direct Link To This Post Posted: 21 Sep 2024 at 7:43am
If it's plastic you might try leaving it off for a month or so. Remove it completely not just loose, need to get it away from the gas. That works on chain saw caps. 

Edited by Gary (sw Wis.) - 21 Sep 2024 at 7:44am
190XT - D17 - D14 - WD45 w/loader - WD - (2)B110 - 616H - 610 - B-208 - WD with 190 Mounted Corn Picker - All Crop 60
Back to Top
Dave (NE) View Drop Down
Orange Level
Orange Level


Joined: 12 Sep 2009
Location: Eagle Nebraska
Points: 2148
Post Options Post Options   Thanks (0) Thanks(0)   Quote Dave (NE) Quote  Post ReplyReply Direct Link To This Post Posted: 21 Sep 2024 at 8:33am
Yes, it is plastic.  So, keeping it away from the gas fumes will let it expand back out?
Do not argue with an idiot. He will drag you down to his level and beat you with experience. Mark Twain.
Back to Top
Gary (sw Wis.) View Drop Down
Silver Level Access
Silver Level Access


Joined: 12 Sep 2009
Location: S.W. Wis.
Points: 207
Post Options Post Options   Thanks (0) Thanks(0)   Quote Gary (sw Wis.) Quote  Post ReplyReply Direct Link To This Post Posted: 21 Sep 2024 at 4:46pm
Yes, I do it with chain saw caps all the time. The chain saw cap fit inside the tank and your mower cap go over the neck but I think it's worth a try.
One more thought is the tank plastic? If so it may have expanded.
I would like to know if it works.


Edited by Gary (sw Wis.) - 21 Sep 2024 at 4:53pm
190XT - D17 - D14 - WD45 w/loader - WD - (2)B110 - 616H - 610 - B-208 - WD with 190 Mounted Corn Picker - All Crop 60
Back to Top
Dave (NE) View Drop Down
Orange Level
Orange Level


Joined: 12 Sep 2009
Location: Eagle Nebraska
Points: 2148
Post Options Post Options   Thanks (0) Thanks(0)   Quote Dave (NE) Quote  Post ReplyReply Direct Link To This Post Posted: 21 Sep 2024 at 5:29pm
Tank is not plastic.
Do not argue with an idiot. He will drag you down to his level and beat you with experience. Mark Twain.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.063 seconds.


Help Support the
Unofficial Allis Forum