#77 Rake Teeth Clips
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=45974
Printed Date: 18 Jul 2025 at 3:07pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: #77 Rake Teeth Clips
Posted By: Dave (NE)
Subject: #77 Rake Teeth Clips
Date Posted: 21 Feb 2012 at 7:00pm
I posted this on the classified link without any responses, so wanted to run it by the forum. I am in need of the clips/brackets used to mount the teeth on a model #77 rake. They are approximately 4 1/2" long and 1 1/4" high. Here is a picture of what I need. I need about a dozen of them. Agco can get them for $8.47 each or some aftermarket they have for $5.36 each. Would like some used ones for a little less. Either respond here, PM me, or if it is easier you may call my cell at 402-540-5987. Also, if someone has a manual for the #77M rake it would be appreciated. I need to figure out how to adjust the height. I think it is on the rear wheels, but would like to confirm. Thanks, Dave  |
Replies:
Posted By: Dave (NE)
Date Posted: 24 Feb 2012 at 8:50am
| Going to bump this back up to see if there is any response. If I can't locate these clips used, I'll probably have to go thru Agco and pick them up. Unfortunately, I need quite a few which tends to add up when buying new. Also, I'm interested in a manual for the #77M rake. I think I've figured out the height adjustment, but would like to confirm via a manual. Thanks, Dave |
Posted By: Fastcars63
Date Posted: 24 Feb 2012 at 10:29am
| Since it already has some rake teeth from New Holland would the clip that holds them to a NH rake work. I understand if you are wanting it to look original and want the OEM. |
Posted By: David Grubb
Date Posted: 24 Feb 2012 at 11:28am
|
You could give these guys a try: http://www.sloanex.com/hay-and-baler-parts.html?cat=2928. Sometimes the AC rakes and the New Idea rakes parts would interchange.
------------- Dave |
Posted By: bryan/silex
Date Posted: 24 Feb 2012 at 11:52am
| I know they wouldn't be original, but what about the single teeth clips like for a new holland rake and just use one per tooth. |
Posted By: farminharmon
Date Posted: 24 Feb 2012 at 12:12pm
|
To use the new holland teeth you will need to redrill the holes in the bar because the bolt sizes are different for new holland and you cant keep the teeth tight with the smaller bolt. ------------- B110 CA D10II (2)D12III 5040 5050 6080 170 JD5205 Kubota M9000 Kubota M95S |
Posted By: ctbowles58
Date Posted: 24 Feb 2012 at 3:54pm
------------- 190XT 2WD45 WF D15 D14 CA BIG10 302 & 303 bailers 77G rake 80R mower 6 plows and alot more |
farminharmon wrote:Posted By: CTuckerNWIL
Date Posted: 24 Feb 2012 at 5:38pm
|
You might be able to buy steel channel bent to that shape. You would have to drill holes and cut the notches. As long as your labor ain't worth nothin you might save a little.
------------- http://www.ae-ta.com" rel="nofollow - http://www.ae-ta.com Lena 1935 WC12xxx, Willie 1951 CA6xx Dad bought new, 1954WD45 PS, 1960 D17 NF |