All-Crop snap coupler grain drill.
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=206507
Printed Date: 30 Apr 2025 at 8:24pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: All-Crop snap coupler grain drill.
Posted By: TomYaz
Subject: All-Crop snap coupler grain drill.
Date Posted: 30 Apr 2025 at 11:15am
|
Question on its operation... Is the use of the hydraulic "hold position" necessary to use this unit, or is just a drop to the ground deal? Thinkin about getting one to play with but I despise the hold position setting on the WD45...... ------------- If its not an All-Crop, it all crap! |
Replies:
Posted By: SteveM C/IL
Date Posted: 30 Apr 2025 at 1:22pm
| Only other thing you can do is set it for TB. Realize that it will drop quicker with less control and lever has to be full up all the while when raised. What's the issue with hold position? |
Posted By: Allis dave
Date Posted: 30 Apr 2025 at 1:25pm
|
It's not suggested to use the TB setup and use it to hold up equipment for long periods of time. DR has advised against this. I also find the hold positon odd and annoying, but I was usint it once while disking and left it up for a but and it locked up the hydraulics. Everything was stuck "up". U had to loosen the coupler to relieve pressure to get everything working again. I suppose I find it annoying becasue the hold detent is so strong. It's difficult to jerk it up and down for a minor adjustment.
|
Posted By: TomYaz
Date Posted: 30 Apr 2025 at 1:59pm
|
<<It's difficult to jerk it up and down for a minor adjustment.>> yep...pain when I want to set it up a bit up or down with brush hog. Would think adjusting for a grain drill is more exacting. ...not interested in that...screw it... ------------- If its not an All-Crop, it all crap! |
Posted By: Don(MI)
Date Posted: 30 Apr 2025 at 2:34pm
|
Tom, the spring coils control about 6-8" of vertical movement on each disc and seed tube across the width of the drill. I would think it's no issue. We have used the same drill on both WD and D14 without any issues on hold positions. I think the vertical travel helps make up any differential with the hold pos. Of the tractor. If that makes sense... ------------- Galatians 5:22-24 "I got a pig at home in a pen and corn to feed him on, All I need is a pretty little girl to feed him when I'm gone!" |
Posted By: Don(MI)
Date Posted: 30 Apr 2025 at 2:35pm
 ------------- Galatians 5:22-24 "I got a pig at home in a pen and corn to feed him on, All I need is a pretty little girl to feed him when I'm gone!" |
Posted By: DiyDave
Date Posted: 30 Apr 2025 at 3:18pm
|
If you're looking for one, I have one to sell... ------------- Source: Babylon Bee. Sponsored by BRAWNDO, its got what you need! |
Posted By: den/southern illinoi
Date Posted: 30 Apr 2025 at 3:46pm
|
The one I had actually hung off the rock shaft. Just have to adjust the chains to allow the drill to be at the right depth. Do not need to hold with the hydraulics. ------------- Own 4 wheel 20, 2-5015, 5020 and associated equipment and 2 electric forklifts. |
Posted By: dr p
Date Posted: 30 Apr 2025 at 7:37pm
|
I just planted 13 acres of oats with one of those drills. The rockshaft chains hold it in place and there is an adjustment to help hold pressure on the openers. The fertilizer adjustment is pretty crude and the seed adjustment requires flipping a bunch of gears around. The biggest problem is the capacity is crazy small. Six bushels for grain and 400 pounds of fertilizer. I like old obsolete allis equipment as much as anyone but this may be a machine best left in the back of the shed. Or maybe i am just exhausted from lugging bags of seeds in the 85 degree heat. My grandfather was a lot more tough than i. |