clutch alignment tool
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=183492
Printed Date: 07 Aug 2025 at 7:41pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: clutch alignment tool
Posted By: Kevin210
Subject: clutch alignment tool
Date Posted: 26 Sep 2021 at 9:05pm
I'm looking for an alignment tool for a 210 allis,would like to have one of my own if possible.
I'm in Indiana.
|
Replies:
Posted By: Charlie175
Date Posted: 27 Sep 2021 at 5:41am
Some of the manuals show you a diagram of the tool so you can make it.
-------------
Charlie
'48 B, '51 CA, '56 WD45 '61 D17, '63 D12, '65 D10 , '68 One-Ninety XTD
|
Posted By: jaybmiller
Date Posted: 27 Sep 2021 at 5:57am
shh, I used a broom handle,20 year ago and Troy's still happily running.
-------------
3 D-14s,A-C forklift, B-112
Kubota BX23S lil' TOOT( The Other Orange Tractor)
Never burn your bridges, unless you can walk on water
|
Posted By: plummerscarin
Date Posted: 27 Sep 2021 at 6:23am
|
Jay, it's no secret. I did the same on a 170
|
Posted By: MACK
Date Posted: 27 Sep 2021 at 7:17am
|
With a recessed flywheel, it caint be off very far. MACK
|
Posted By: DrAllis
Date Posted: 27 Sep 2021 at 7:17am
|
Pretty sure the D21/210/220 takes the exact same tooling as any big frame Farmall from 806 and up.
|
Posted By: Charlie175
Date Posted: 27 Sep 2021 at 8:12am
|
DJS has them
https://stores.djstractorparts.com/clutch-alignment-tool-10-spline/" rel="nofollow - https://stores.djstractorparts.com/clutch-alignment-tool-10-spline/
-------------
Charlie
'48 B, '51 CA, '56 WD45 '61 D17, '63 D12, '65 D10 , '68 One-Ninety XTD
|
Posted By: jaybmiller
Date Posted: 27 Sep 2021 at 8:30am
was told every 'clutch kit' is sold WITH the alignment tool, maybe hit local garage, see what they have...
-------------
3 D-14s,A-C forklift, B-112
Kubota BX23S lil' TOOT( The Other Orange Tractor)
Never burn your bridges, unless you can walk on water
|
Posted By: AC720Man
Date Posted: 27 Sep 2021 at 1:50pm
I just replaced both clutches in my 160, as Charlie said my manual gave me exact measurements for my local machine shop to make me one out of aluminum. $25, so much better than the plastic ones that can break or flex.
-------------
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
Posted By: DougG
Date Posted: 27 Sep 2021 at 3:56pm
|
This is my experience, and I always try to do things right- the clutch disc is so close to being centered- gently tighten the pressure plate bolts ; look from behind , and center the disc with a screwdriver or something like that in the pilot bearing - its very simple
|
Posted By: DaveSB
Date Posted: 27 Sep 2021 at 5:09pm
Maybe I’m just lucky, but I haven’t used a clutch alignment tool for the past ten years, just eye ball them and slide the tractor together.
Good luck
if you need one you can make one out of wood on a wood llathe, unless extremely heavy clutch plate.
-------------
1948 C, 1953 CA, 1948 WD, 1961 D-17 Series 2 Diesel, 1939 WC, 1957 D14
|
Posted By: AC720Man
Date Posted: 27 Sep 2021 at 8:41pm
That may work on a tractor with just a transmission clutch, I wouldn’t attempt it with a dual stage clutch such as in my 160. The clutches can’t take misalignment and will bend very easily. The entire clutch assembly weighs 70 lbs.
-------------
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
Posted By: Kevin210
Date Posted: 01 Oct 2021 at 9:06pm
Finally got the MK II 3700 engine bolted up this morning on the 210
and did some painting.
I only have 3 days a week to work on it due to working 12 hour shifts
Monday-Thursday and have other things to do also but it's coming along.
|
|