80T trailer type mower -info needed
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=136705
Printed Date: 08 Nov 2025 at 11:56am
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: 80T trailer type mower -info needed
Posted By: Farmer Tom
Subject: 80T trailer type mower -info needed
Date Posted: 28 Mar 2017 at 11:06am
|
I am working on my 80T mower and need a little info/help on a couple of items. If anyone can help, it would be appreciated. First, the "lift cable" for this mower is no longer available from AGCO and I need to have one made. To do this, I need the size of the cable used, its overall length and any other information that will help in making a new cable for it. Or, if anyone has one available, I would be interested. Second, the mower did not come with a "hydraulic cylinder", so I need to know what size (bore, stroke, length) that I should get to put on the mower. Thanks in advance for any information given! 
|
Replies:
Posted By: PaulB
Date Posted: 28 Mar 2017 at 3:47pm
|
Where are you located? I have a NOS lift cable, although I do not know for sure which mower it is for. I also have a few good AC hydraulic cylinders you could choose from. I'm in Maryland very near Gettysburg Pa.
------------- If it was fun to pull in LOW gear, I could have a John Deere. Real pullers don't have speed limits. If you can't make it GO... make it SHINY |
Posted By: Mikez
Date Posted: 28 Mar 2017 at 10:22pm
| Do you have a part number for the cable |
Posted By: Farmer Tom
Date Posted: 29 Mar 2017 at 12:06am
| Mikez: According to the AGCO parts book, the lift cable is part #70804360. |
Posted By: Farmer Tom
Date Posted: 29 Mar 2017 at 12:17am
|
PaulB: I am in Columbus, OH (Central Ohio). I think, although I am far from being any type of expert, a lift cable was only used on the 80T mower. The next model, 82T, was a directly connected hydraulic cylinder connected to the sickle bar to the best of my knowledge. The preceding mower, a #7 trailer mower - of which I had one quite a few years back, did not use a any cable for its lift system as I remember. The lift cable part number I am looking for, according to the AGCO parts book, is #70804360. Does this number match up to your NOS cable? Based on what I have found out, I think I have the hydraulic cylinder covered. Thanks, Farmer Tom |
Posted By: Eldon (WA)
Date Posted: 29 Mar 2017 at 12:49am
|
The 80R (rear mounted) used a cable and I believe the 80S (front side mount) also used a cable. The old part number you would be looking for is 804360 - later replacement numbers added the 70 ahead of the original numbers. That part number just says "80" in my book, so it might be the same cable for all the 80 mowers. ------------- ALLIS EXPRESS! This year: |
Posted By: Mikez
Date Posted: 29 Mar 2017 at 9:12am
| Dads going to see if we have one in parts bin. I'm pritty sure there's a 80T mower minus the bar and gear box in our barn from when my grandfather was a dealer. I looked after I asked you for number and found parts book and it shows dif part numbers for 80T,80Sand80T |
Posted By: Mikez
Date Posted: 29 Mar 2017 at 11:47pm
| Don't have it in parts bin. Would have to try to get in barn to see if there's a cable on that mower in there. |