This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
190 XT oil cooler |
Post Reply |
Author | |
DSeries4
Orange Level Joined: 12 Sep 2009 Location: Ontario, Canada Points: 7204 |
Post Options
Thanks(0)
Posted: 23 Nov 2015 at 10:23pm |
'49 G, '54 WD45, '55 CA, '56 WD45D, '57 WD45, '58 D14, '59 D14, '60 D14, '61 D15D, '66 D15II, '66 D21II, '67 D17IV, '67 D17IVD, '67 190XTD, '73 620, '76 185, '77 175, '84 8030, '85 6080
|
|
Sponsored Links | |
screwloose
Orange Level Joined: 06 Dec 2014 Location: maryland Points: 361 |
Post Options
Thanks(0)
|
Oil cooler has tubes that run from end to end that the coolant runs through, engine oil runs through the outside of those tubes hence the coolant cools the oil. Oil drains back into the oil pan, coolant keeps circulating through engine anf radiator.
|
|
screwloose
Orange Level Joined: 06 Dec 2014 Location: maryland Points: 361 |
Post Options
Thanks(0)
|
Oil drains back to the oil pan or oil gallery
|
|
Orange Blood
Orange Level Joined: 29 Nov 2010 Location: ColoradoSprings Points: 4053 |
Post Options
Thanks(0)
|
Looks like you may just need to tighten your clamps. Worst case you may want to rebuild the hoses. Not a hard job, and Agco still has all the parts, new hoses, and new heat shields, clean the hose flanges up on a wire wheel and you should be golden.
|
|
Still in use:
HD7 WC C CA WD 2-WD45 WD45LP WD45D D14 3-D17 D17LP 2-D19D D19LP 190XTD 190XTLP 720 D21 220 7020 7030 7040 7045 3-7060 Projects: 3-U UC 2-G 2-B 2-C CA 7-WC RC WDLP WF D14 D21 210 7045 N7 |
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 19552 |
Post Options
Thanks(0)
|
When replacing the hose, use two new clamps to squeeze the hose ends and then wrap the heat shield around them and use a third clamp in the middle to hold the heat shield. This provides better clamping of the hose.
|
|
MACK
Orange Level Joined: 17 Nov 2009 Points: 7664 |
Post Options
Thanks(0)
|
Oil comes from pump through cooler, then into oil gallery to lube mains, rods,turbo, and valve train. MACK
|
|
SteveM C/IL
Orange Level Access Joined: 12 Sep 2009 Location: Shelbyville IL Points: 8005 |
Post Options
Thanks(0)
|
Hey Fred! If it only held oil....what is cooling it?
|
|
slip knot
Silver Level Joined: 15 Aug 2014 Location: texas Points: 103 |
Post Options
Thanks(0)
|
That's an odd sized hose. 2 1/8 IIRC or 54mm. I had to buy a 3 ft piece when I replaced mine. I bought the HD 4ply hose and it was a real bear to get on. Way tight against the block at the waterpump area.
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |